About s309973

s309973 · 07-20-2005

I've multiple switches, with the core being in "Server" and the connecting switches being "Clients". All of these devices show information when executing "sh vtp status", for example - but none of them have any VTP-related configuration statements. ...

s309973 · 07-19-2005

I am reviewing one of our WAN routers, on an infrastructure I have recently inherated, and noted an EIGRP configuration which doesn't make much sense to me. I'm wondering if I misunderstand the intent. The WAN router has the following EIGRP configu...

s309973 · 07-12-2005

I misconfigured my ACS authentication (or something) and need to console into my VPN 3005 concentrator and undo my changes to restore my admin access to the device. However, I'm having problems consoling into the device.I'm using the standard robin-...

s309973 · 07-12-2005

Running into a problem. Probably something simple I'm overlooking.I am trying to configure my Cisco VPN 3005 Concentrator to use my Cisco ACS server for administrative authentication rights, versus using local authentication. My Cisco ACS is config...

s309973 · 06-27-2005

I have a PIX 501 at a remote user's house that VPNs into our Cisco 3000 series concentrator. The user has been complaining of frequent disconnections and during troubleshooting I noticed that anytime I type the commands "show log" or "show proc", my...

s309973 · 07-20-2005

My 4507R doesn't have a "dir flash:" command. I have...4500-SW1#dir ? /all List all files /recursive List files recursively all-filesystems List files on all filesystems bootflash: Directory or file name ...

s309973 · 07-12-2005

Pretty sure I know what I did wrong, now I just need to know how to recover from my error. I didn't specify ann AAA Access Level as 15 within the concentrator's "Access Rights" / "Administrator". However, now I need to figure out how to restore my ...

s309973 · 06-27-2005

Some additional information...I ran Ethereal while I was telnetted into the remote PIX501 to see if I was receiving the output of my "show log", at a packet level, but perhaps the Telnet application wasn't presented it on the screen. Ethereal report...

s309973 · 06-27-2005

I had the same need a little over a year ago and I opened a TAC case to ask if there were any "undocumented commands" to get the PIX to route packets in/out, for my particular SOHO need. I was advised it was NOT possible. I had to put a router just...

s309973 · 06-24-2005

(Part 3 of 3)Jun 24 11:52:40.470 CDT: %SYS-5-CONFIG_I: Configured from console by ciscoadmin on vty0 (172.16.15.121)CMD: 'show cdp nei' 11:53:0 CDT Fri Jun 24 2005CMD: 'show shut' 11:53:37 CDT Fri Jun 24 2005CMD: 'show shut' 11:53:38 CDT Fri Jun 24 2...

Member Since	‎11-14-2001 09:47 PM
Date Last Visited	‎08-18-2017 03:51 AM
Posts	61
Total Helpful Votes Received	7

User Statistics

User Activity

Are VTP config lines not included in configurations?

EIGRP and Distribute-list commands

Consoling into the VPN 3005 Concentrator

Configuring VPN concentrator to use Cisco ACS for admin authen

PIX 501 - 6.3(1) Disconnection from device after 'show log'

Re: Are VTP config lines not included in configurations?

Re: Configuring VPN concentrator to use Cisco ACS for admin auth

Re: PIX 501 - 6.3(1) Disconnection from device after 'show log'

Re: Route in/out same interface on PIX

Re: Catalyst 4000 - Config registers and error crashes