Hello people I'm having a problem creating a VPN. The VPN raises and works without problems, but running the AS400 takes about 30 to 40 minutes to complete the process, but the TCP session closes the AS400 administration window at 1 minute. Al already modify all the parameters in "Platform Configuration", but still it is closing the TCP session. The parameter that does not allow me to modify and I can not see from the Firesight is the "timeout conn-hold down". How could you modify this in the FTD? Or if someone already had a similar case if you could give me a hand. Thank you very much. ... View more

hello I'm having problems with the version of IOS C2900-universalk9-mz.SPA.153-3.M4.bin, each time the router is restarted ssh is disabled and is unable to connect remotely activating the local authentication only works for me. Someone already had this problem? I had to install the previous version to this IOS to work. Current version with which it works is C2900-universalk9-mz.SPA.152-4.M4.bin. I appreciate the help. ... View more

Buenas Me encuentro con el siguiente problema, configure HSRP en los router's de borde de la empresa en donde trabajo, los dos se reconocen sin problema, abajo de los mismos se encuentra un switch que interconecta los router de borde con los ASA's en failover, toda la red se comunica por medio de EIGRP, el problema esta que todo el trafico debe de ir por el borde 1, cosa que no esta pasando, ya que al verificar el ASA aprende la ruta hacie el borde 2 y no hacia el borde 1 que seria el principal, describire una configuracion de ejemplo como para que puedan tener idea y si pueden darme una mano con este incomveniente, desde ya agradezco la ayuda. PD.: los dos bordes estan configurados de la misma manera, solo cambia la ip de de la vlan de administracion con la cual se estan comunicando.}         Tambien identifique que la interface del borde 2 tiene la mac-address mas baja que la del borde 1, creo que no debe afectar pero no esta demas           la info.         Tambien les comento que trafico entra por el borde 1, el problema que identifique es que en el ASA cuando busca la salida da como prioridad el           borde2, si tener ninguna ruta por defecto hacia ella, incluso al realizar un show route, me indica que es el borde 1 el principal. Saludos. Carlos Báez. CCNA -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- config. HSRP - borde 1 VLAN10 ip address 172.30.1.9 255.255.255.0 stanbye 1 ip 172.30.1.1 stanbye 1 priority 200 stanbye 1 timer 1 5 stanbye 1 preempt router eigrp 100 redistribute static no auto-summary network 172.30.1.0 0.0.0.255 network 192.168.1.0 0.0.0.255 ip route 0.0.0.0 0.0.0.0 1.1.1.1 --- Gateway ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- HSRP - borde 2 VLAN10 ip address 172.30.1.10 255.255.255.0 stanbye 1 ip 172.30.1.1 stanbye 1 timer 1 5 router eigrp 100 redistribute static no auto-summary network 172.30.1.0 0.0.0.255 network 192.168.1.0 0.0.0.255 ip route 0.0.0.0 0.0.0.0 1.1.1.1 --- Gateway -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ASA interface Ethernet0/1 description Conectado Borde nameif outside security-level 0 ip address 172.30.1.3 255.255.255.0 standby 172.30.1.4 router eigrp no auto-summary network 172.30.1.0 0.0.0.255 ... View more

Hello, could give me a hand with a problem. I have a cisco 1811 router w, wan interface tells me that this up, even to acknowledge and connect up the same, but there is no connection, we ping and do not respond, it's like it is locked. please if anyone has a solution I'll be very grateful. thanks ... View more

hello I have two router's 1811 and have problems when starting the router's mistake shows up the next Failed test all 0xffffffff Bad RAM at location 0x8800085C: wrote 0xFFFFFFFF, read 0xFFDFFFFF region failed 8800083C: FFFFFFFF 88000840: FFFFFFFF 88000844: FFFFFFFF 88000848: FFFFFFFF 8800084C: FFFFFFFF 88000850: FFFFFFFF 88000854: FFFFFFFF 88000858: FFFFFFFF 8800085C: FFDFFFFF 88000860: FFFFFFFF 88000864: FFFFFFFF 88000868: FFFFFFFF 8800086C: FFFFFFFF 88000870: FFFFFFFF 88000874: FFFFFFFF 88000878: FFFFFFFF I would appreciate if you can help me with this problem. Thank you very much. Carlos ... View more