Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About smailag00
08-18-2017
Stats
Member since
11-22-2012
5
Posts
0
Helpful
0
Solutions
01-17-2013
07:41 AM
hi i already put this topic : https://supportforums.cisco.com/thread/2184033 actually it's working fine i just add this command to the config: track 1 interface Dialer0 ip routing delay up 30 ! track 2 interface Dialer1 ip routing delay up 30 ! track 3 interface Dialer2 ip routing delay up 30 ! track 4 interface GigabitEthernet0/1 ip routing delay up 30 ip route 0.0.0.0 0.0.0.0 Dialer0 track 1 ip route 0.0.0.0 0.0.0.0 Dialer1 track 2 ip route 0.0.0.0 0.0.0.0 Dialer2 track 3 ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1 172.20.1.1 track 4
... View more
01-17-2013
04:57 AM
Router :cisco 2901 with securityk9 licence I used this manual : http://cisco.sitecelerate.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SY/configuration/guide/web_authentication.html#wp1083487 Im traying to change de login page but the commande dosen't work : ip admission proxy http login page file disk1:login.htm This is what I see when I type (config)#ip admission ? absolute-timer Absolute Timeout in minutes auth-proxy-audit Authentication Proxy Auditing auth-proxy-banner Authentication Proxy Banner http Configure maximum HTTP process inactivity-timer Inactivity Timeout in minutes init-state-timer Init State Timeout in minutes max-login-attempts Max Login attempts per user max-nodata-conns Max TCP NODATA Connections name Specify an Authentication/Admission Rule ratelimit Session Ratelimit source-interface IP Admission Source Interface watch-list Watch-list --------------- Seems like its missing the 'ip admission proxy' command so are there other commands that can help me to change the login page of the router proxy? thanks
... View more
Labels:
11-23-2012
01:33 PM
Thank you very much,this solution works fine . I tested with 'show ip nat translation ' ,'show ip cef ',and i found that the tree lines works . In a few days I have to add a new isp connection to the gigabitEthernet 0/1 interface which is connected to another router 10.0.0.1(a specialized line). i think i have to do this : interface gigabitEthernet 0/1 ip address 10.0.0.2 255.255.255.248 no sh ip nat outside ip load-sharring peer paquet route-map DIAL3 p 10 match ip add 1 match int gigabitEthernet 0/1 ip nat inside source route-map DIAL3 interface gigabitEthernet 0/1 overload ip route 0.0.0.0 0.0.0.0 gigabitEthernet0/1 10.0.0.1 is this a good configuration ?
... View more
11-22-2012
02:32 PM
i have a cisco router 2901 /ipbasek9 with 3 adsl interfaces .i tried to do a load balancing and bonding the 3 adsl lines without success. this is my current configuration : version 15.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ! boot-start-marker boot-end-marker ! ! logging buffered 51200 warnings ! no aaa new-model ! no ipv6 cef ipv6 spd queue min-threshold 62 ipv6 spd queue max-threshold 63 ip source-route ip cef ! ! ! ip dhcp excluded-address 172.20.1.1 ! ip dhcp pool client import all network 172.20.0.0 255.255.0.0 dns-server 212.217.0.1 212.217.1.1 default-router 172.20.1.1 ! ! ip domain name yourdomain.com ip name-server 212.217.0.1 ip name-server 212.217.1.1 multilink bundle-name authenticated ! ! crypto pki token default removal timeout 0 ! crypto pki trustpoint TP-self-signed-1607540217 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-1607540217 revocation-check none rsakeypair TP-self-signed-1607540217 ! ! crypto pki certificate chain TP-self-signed-1607540217 certificate self-signed 01 !..............................! quit license udi pid CISCO2901/K9 sn ******* ! ! username ***** privilege 15 password 0 ***** ! ! ! ! ! ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$ ip address 172.20.1.1 255.255.0.0 ip nat inside ip virtual-reassembly in duplex auto speed auto ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! interface ATM0/0/0 no ip address ip load-sharing per-packet no atm ilmi-keepalive ! interface ATM0/0/0.1 point-to-point pvc 8/35 pppoe-client dial-pool-number 1 ! ! interface ATM0/1/0 no ip address ip load-sharing per-packet no atm ilmi-keepalive ! interface ATM0/1/0.1 point-to-point pvc 8/35 pppoe-client dial-pool-number 2 ! ! interface ATM0/2/0 no ip address ip load-sharing per-packet no atm ilmi-keepalive ! interface ATM0/2/0.1 point-to-point pvc 8/35 pppoe-client dial-pool-number 3 ! ! interface ATM0/3/0 no ip address shutdown no atm ilmi-keepalive ! interface Dialer0 ip address negotiated ip mtu 1452 ip nat outside ip virtual-reassembly in encapsulation ppp dialer pool 1 dialer-group 1 ppp authentication chap pap callin ppp chap hostname ***** ppp chap password 0 ****** ppp pap sent-username ***** password 0 ***** ! interface Dialer1 ip address negotiated ip mtu 1452 ip nat outside ip virtual-reassembly in encapsulation ppp dialer pool 2 dialer-group 2 ppp authentication chap pap callin ppp chap hostname ***** ppp chap password 0 ***** ppp pap sent-username ***** password 0 ***** ! interface Dialer2 ip address negotiated ip mtu 1452 ip nat outside ip virtual-reassembly in encapsulation ppp dialer pool 3 dialer-group 3 ppp authentication chap pap callin ppp chap hostname ***** ppp chap password 0 ***** ppp pap sent-username ***** password 0 ***** ! ip forward-protocol nd ! ip http server ip http access-class 23 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ip nat inside source list 1 interface Dialer0 overload ip nat inside source list ADSL2 interface Dialer2 overload ip nat inside source list adsl2 interface Dialer1 overload ip route 0.0.0.0 0.0.0.0 Dialer0 ip route 0.0.0.0 0.0.0.0 Dialer1 ip route 0.0.0.0 0.0.0.0 Dialer2 ! ip access-list standard ADSL2 remark CCP_ACL Category=2 permit 172.20.0.0 0.0.255.255 ip access-list standard adsl2 remark CCP_ACL Category=2 permit 172.20.0.0 0.0.255.255 ! access-list 1 remark INSIDE_IF=GigabitEthernet0/0 access-list 1 remark CCP_ACL Category=2 access-list 1 permit 172.20.0.0 0.0.255.255 dialer-list 1 protocol ip permit dialer-list 2 protocol ip permit dialer-list 3 protocol ip permit ! ! ! control-plane ! thanks
... View more
Labels:
01-17-2013
hii already put this topic
:https://supportforums.cisco.com/thread/2184033actually it's working
fine...
11-23-2012
Thank you very much,this solution works fine .I tested with 'show ip nat
translation ' ,'show ip cef...
Public Statistics
| Date Registered | 11-22-2012 02:01 PM |
| Date Last Visited | 08-18-2017 03:56 AM |
| Total Messages Posted | 5 |
