Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About pramod.maharana
Stats
Member since
04-25-2012
4
Posts
5
Helpful
0
Solutions
Created by
pramod.maharana
in Wireless and Mobility
in Wireless and Mobility
05-08-2013
11:31 PM
05-08-2013
11:31 PM
We are getting below errors frequently on Cisco 5508 WLC. These error messages started to came recently. *apfReceiveTask: May 03 09:43:44.180: #APF-3-LOCALHANDOFF: apf_mm.c:108 00:88:65:a9:07:24 0.0.0.0 DHCP_REQD (7) Unable to anchor locally *apfReceiveTask: May 03 09:43:44.180: #MM-1-USER_NOT_ALLOWED: mm_mobile.c:3632 Unable to allow user into the system. perhaps already logged on. *apfReceiveTask: May 03 08:47:23.735: #APF-3-LOCALHANDOFF: apf_mm.c:108 14:36:05:49:28:98 172.29.116.122 RUN (20) Unable to anchor locally *apfReceiveTask: May 03 08:47:23.735: #MM-1-USER_NOT_ALLOWED: mm_mobile.c:3632 Unable to allow user into the system. perhaps already logged on. *apfReceiveTask: May 02 22:44:15.530: #APF-3-LOCALHANDOFF: apf_mm.c:108 18:20:32:50:c9:2d 172.29.116.131 RUN (20) Unable to anchor locally *apfReceiveTask: May 02 22:44:15.530: #MM-1-USER_NOT_ALLOWED: mm_mobile.c:3632 Unable to allow user into the system. perhaps already logged on. *apfReceiveTask: May 02 20:50:24.092: #APF-3-LOCALHANDOFF: apf_mm.c:108 f8:1e:df:65:c5:68 172.29.116.175 RUN (20) Unable to anchor locally *apfReceiveTask: May 02 20:50:24.091: #MM-1-USER_NOT_ALLOWED: mm_mobile.c:3632 Unable to allow user into the system. perhaps already logged on. *apfReceiveTask: May 02 20:31:04.043: #APF-3-LOCALHANDOFF: apf_mm.c:108 00:13:02:bb:18:7e 172.29.116.125 RUN (20) Unable to anchor locally *apfReceiveTask: May 02 20:31:04.042: #MM-1-USER_NOT_ALLOWED: mm_mobile.c:3632 Unable to allow user into the system. perhaps already logged on. *apfReceiveTask: May 02 20:30:49.186: #APF-3-LOCALHANDOFF: apf_mm.c:108 00:13:02:bb:18:7e 0.0.0.0 DHCP_REQD (7) Unable to anchor locally *apfReceiveTask: May 02 20:30:49.186: #MM-1-USER_NOT_ALLOWED: mm_mobile.c:3632 Below is the sysinfo ---------------Show boot--------------- Primary Boot Image............................... 7.4.100.0 (active) Backup Boot Image................................ 7.0.230.0 The message APF-3-LOCALHANDOFF seems to be internal system error on WLC. I have been trying to find any bugs relating to case but no luck. http://www.cisco.com/en/US/docs/wireless/controller/message/guide/msgs2.html#wp1005526 Appreciate any help on this.
... View more
Labels:
Created by
pramod.maharana
in Routing
in Routing
06-24-2012
12:50 AM
06-24-2012
12:50 AM
Thanks Davaid, I got link on support forum only i.e. Cisco 1841 and 2801 doesn’t have temperature sensor & doesn't show temperature in the “show environment all” output. https://supportforums.cisco.com/thread/196056 And the closest document : "%ENVMON-3-OVERTEMP_OK: System temperature normal" messages doesn't supported on Cisco 2801. http://www.cisco.com/en/US/docs/routers/access/2800/hardware/installation/guide/07_hw.html#wp1004092
... View more
Created by
pramod.maharana
in Routing
in Routing
06-20-2012
05:57 AM
06-20-2012
05:57 AM
Dear All, We have a Cisco 2801 router running IOS "c2801-spservicesk9-mz.151-4.M4.bin" which we upgraded from previous “c2801-spservicesk9-mz.124-3d.bin”. Requirement. We want to monitor the device temperature via snmp but unable to do because temperature ratings are not available on "show environment all" output like below. Routeri# sh environment all Fan 1 OK Fan 2 OK ILP Power Supply - Absent Fan Speed Setting: Normal Where as on Cisco 2811/51 & Cisco 3825/45 we can get temperature ratings on "show env all" output. As per link http://www-tss.cisco.com/eservice/elearning/router/cisco2800/doc/e-learning.pdf below commands are supported on Cisco 2800 series router. Command options • show environment all • show environment fans • show environment leds • show environment power-supply • show environment table • show environment temperatures • show environment voltages I want to know whether this is Cisco 2801 platform limitations or something else. tried to find Cisco doc on this but no luck. Thanks in Advance.
... View more
Labels:
04-25-2012
04:20 AM
Thanks for this suggestion i have solved this problem using this.
... View more
Created by
pramod.maharana
in Wireless and Mobility
05-08-2013
05-08-2013
We are getting below errors frequently on Cisco 5508 WLC. These error
messages started to came recen...
Created by
pramod.maharana
in Routing
06-24-2012
06-24-2012
Thanks Davaid,I got link on support forum only i.e. Cisco 1841 and 2801
doesn’t have temperature sen...
Created by
pramod.maharana
in Routing
06-20-2012
06-20-2012
Dear All,We have a Cisco 2801 router running IOS
"c2801-spservicesk9-mz.151-4.M4.bin" which we upgra...
Public Statistics
| Date Registered | 04-25-2012 04:18 AM |
| Date Last Visited | 09-19-2018 06:53 AM |
| Total Messages Posted | 4 |
| Total Helpful Votes Received | 5 |
