Cisco Community
English
Register
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
michaelstump
‎08-18-2017
Beginner
Recent Badges
Awards
Stats
Member since ‎07-26-2012
18
Posts
5
Helpful
0
Solutions

Nexus 1000v setup on UCS- VMware Infra getting started- help!

Created by in Unified Computing System Discussions
08-11-2013
08-11-2013
Jose,Let's just start with question 1. The 1000v is difficult to set up and configure the first few ...

Activate IOM Fail

Created by in Unified Computing System Discussions
05-23-2013
05-23-2013
Ok, well, not sure what that was about, but I finally decided to force the update of the Backup vers...

Activate IOM Fail

Created by in Unified Computing System Discussions
05-23-2013
05-23-2013
Last week, I attempted to update a pair of 2208XPs from 2.0(3b) to 2.0(5a). I followed the upgrade g...

Re: IOM Update Status: Updating

Created by in Unified Computing System Discussions
05-15-2013
05-15-2013
Thanks, Gregory. I've got a case opened now. I'll post the results once we've worked through the iss...

IOM Update Status: Updating

Created by in Unified Computing System Discussions
05-15-2013
05-15-2013
Just curious if anyone else has run into an IOM firmware update that takes forever. I'm working on a...

vSphere 5.1 on Cisco UCS

Created by in Unified Computing System Discussions
01-25-2013
01-25-2013
Is this what you're looking for?https://my.vmware.com/web/vmware/details?downloadGroup=CISCO-ESXI-5....

Strange behaviour of ESXi on SAN

Created by in Unified Computing System Discussions
12-06-2012
12-06-2012
When it boots, does it boot into the ESXi loader? I would expect that behaviour if you were booting ...

UCS Server CPU Allocation

Created by in Unified Computing System Discussions
11-28-2012
11-28-2012
You don't need to have a 1:1 ratio for physical CPUs and vCPUs. You should, if possible, keep your v...

iSCSi booting problem (B230M3 blade)

Created by in Unified Computing System Discussions
11-28-2012
11-28-2012
The second adapter will be 1/1/2. (See http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/cli/...

iSCSi booting problem (B230M3 blade)

Created by in Unified Computing System Discussions
11-27-2012
11-27-2012
The iscsi_get_config will tell you if the iSCSI initiator is able to connect to the target. If you r...

failover properties set at dvswitch level??

Created by in Unified Computing System Discussions
11-27-2012
11-27-2012
AFAIK, this is a feature that has been missing from the dvSwitch for a while now. vSS doesn't suffer...

Re: iSCSi booting problem (B230M3 blade)

Created by in Unified Computing System Discussions
11-27-2012
11-27-2012
One thing you can do it to use the command line to connect to the server's adaptor and collect iSCSI...

Problems with updating B230 to 2.1

Created by in Unified Computing System Discussions
11-21-2012
11-21-2012
Ok. Sorted it out. I had to re-acknowledge both blades and let the discovery process complete. This ...

Problems with updating B230 to 2.1

Created by in Unified Computing System Discussions
11-20-2012
11-20-2012
I've got two B230 M2 blades that are stuck at the same spot in the 2.1 upgrade process. Both are at ...

LAN Connectivity for B-Series blades

Created by in Unified Computing System Discussions
07-26-2012
07-26-2012
Good news: the hosts are finally online.I believe it was a combination of configuration issues conce...
Public Statistics
Date Registered ‎07-26-2012 07:04 AM
Date Last Visited ‎08-18-2017 04:00 AM
Total Messages Posted 18
Total Helpful Votes Received 5
Helpful Votes Given To
See all >
Helpful Votes From
See all >