hi Knows anyone if Cisco Firewall SA520 supports Jumbo Frames? ... View more

Hi I have this Ethernet/Token Ring Router and would like to know howto put the interface TokenRing0/0 up? ETHTR#sh version Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-I-M), Version 12.2(5d), RELEASE SOFTWARE (fc1) Copyright (c) 1986-2002 by cisco Systems, Inc. Compiled Sat 02-Feb-02 03:36 by kellythw Image text-base: 0x80008088, data-base: 0x80989870 ROM: System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1) ETHTR uptime is 7 hours, 3 minutes System returned to ROM by reload System image file is "flash:c2600-i-mz.122-5d.bin" cisco 2612 (MPC860) processor (revision 0x00) with 28672K/4096K bytes of memory. Processor board ID JAE071408W0 (2793660868) M860 processor: part number 5, mask 2 Bridging software. X.25 software, Version 3.0.0. 1 Ethernet/IEEE 802.3 interface(s) 1 Token Ring/IEEE 802.5 interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write) Configuration register is 0x2102 ETHTR#sh interface TokenRing0/0 TokenRing0/0 is down, line protocol is down   Hardware is HAWKEYE, address is 0030.a1a7.dd80 (bia 0030.a1a7.dd80)   Internet address is 10.181.1.10/24   MTU 4464 bytes, BW 16000 Kbit, DLY 630 usec,      reliability 255/255, txload 1/255, rxload 1/255   Encapsulation SNAP, loopback not set   Keepalive set (10 sec)   ARP type: SNAP, ARP Timeout 04:00:00   Ring speed: 16 Mbps   Duplex: half   Mode: Classic token ring station   Full duplex capable   Group Address: 0x00000000, Functional Address: 0x08000000   Ethernet Transit OUI: 0x000000   Last input never, output never, output hang never   Last clearing of "show interface" counters never   Queueing strategy: fifo   Output queue 0/40, 0 drops; input queue 0/75, 0 drops   5 minute input rate 0 bits/sec, 0 packets/sec   5 minute output rate 0 bits/sec, 0 packets/sec      0 packets input, 0 bytes, 0 no buffer      Received 0 broadcasts, 0 runts, 0 giants, 0 throttles      0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort      0 packets output, 0 bytes, 0 underruns      0 output errors, 0 collisions, 327 interface resets      0 output buffer failures, 0 output buffers swapped out      0 transitions ETHTR#sh run ................................. interface TokenRing0/0 ip address 10.181.1.10 255.255.255.0 ring-speed 16 ........................................................ ETHTR#show controllers tokenring 0/0 Interface TokenRing0/0 state: down   Data from IDB:     Current MAC address: 0030.a1a7.dd80, Burned in MAC address: 0030.a1a7.dd80     Group address: 80000000     Functional address: 08000000, enables: CDP     Ring mode: 0000, enables:     Device driver instance pointer: 80F936D8h   Last Ring Status: none     Stats: soft: 0/0, hard: 0/0, sig loss: 0/0            tx beacon: 0/0, wire fault 0/0, recovery: 0/0            only station: 0/0, remote removal: 0/0   Interface failures: 0   Current operating mode:     Classic token ring station       MAC state: not inserted   Internal controller data:     MAC microcode version: 0.00     Hawkeye ASIC revision: 3     Node address: 0000.0000.0000     Functional address: 00000000, Group address: 00000000     Hawkeye ASIC registers:       himr: 00000000h, inpace: 0000h       utility: 7716h, txphthre: 10D0h, rxtxdmathre: 2828h       dmactrl: 0000E01Ch, earlyrxthre: 0000h, llcstop: 0000h       reset: 0002h       txhidescstart: 00000000h, txlodescstart: 00000000h       rxdescstart: 00000000h, srbctrl: 003Eh, descipoll: 3700h       congestcnt: 0000h     Hawkeye transmit error counts:       Underrun: 0/0     Hawkeye receive error counts:       Out of descriptors: 0/0, Giants: 0/0       Corrupted frames: 0/0, CRC errors: 0/0       FIFO overflow: 0/0     Device driver ring buffer data:       Transmit ring:         Ring size: 256 descriptors         Descriptors outstanding: 0         Head pointer: 0   Tail pointer: 0       Receive ring:         Ring size: 64 descriptors         Head pointer: 0     Internal controller soft error counts:       Line errors: 0/0, Internal errors: 0/0       Burst errors: 0/0, ARI/FCI errors: 0/0       Abort errors: 0/0, Lost frame errors: 0/0       Copy errors: 0/0, Receiver congestion: 0/0       Token errors: 0/0, Frequency errors: 0/0     Internal controller SMT state:       Adapter MAC:     0000.0000.0000, Physical drop:       00000000       NAUN address:    0000.0000.0000, NAUN drop:           00000000       Last beacon src: 0000.0000.0000, Last poll:           0000.0000.0000       Last MVID:       0000,           Last attn code:      0000       Txmit priority:  0000,           Auth funct class:    0000       Monitor error:   0000,           Front end errors:    0000       Correlator:      0000,           Soft error timer:    0000       Local ring:      0000,           Ring status:         0000       Beacon rcv type: 0000,           Beacon txmit type:   0000       Last beacon type:0000,           Bcn station NAUN:    0000.0000.0000       Beacon drop:     00000000,       Phantom support:     0000       Access prot req: 0000,           Access prot resp:    0000       Policy flags:    0000,           Protocol event state:0000       Ctrl ring state: 0000,           Protocol join state: 0000       Reserved:        0000,           Protocol mon state:  0000 ... View more

hi Is it possible and howto configure Cisco SA520 firewall for 2 ISP (cable & ADSL) to get load balancing between these ISP? THX ... View more

hi Howto set ports from WS-C2940-8TF-S to full- and half-duplex 100Mbit? THX ... View more

hi Which is the last software release for WS-C2940-8TF-S? I have: IOS (tm) C2940 Software (C2940-I6Q4L2-M), Version 12.1(22)EA8a, RELEASE SOFTWARE (fc1) greetings Piotr ... View more

Hi What are differences between load balancing and load sharing on Cisco MPLS router with BGP? Howto check kind of balancing using CLI? ... View more