Hi Joseph, Thanks for your replay and yes we can connect xconnect but my router seems to me which won't support xconnect or pseudowire  Suppose if we have two geographically separate area and where are two different routers but two router has same network subnet or             R1or L3 Sw-------------------internet------------------------------R2 L3- 1.R1 has two vlans or two subinterfaces like vlan 1 and vlan2 2.Vlan 1 network id 192.168.1.0/24 and Vlan 2 network id 192.168.2.0/24 3.From R2 or remote users want to access my vlan2 192.168.2.0/24 network as they virtually locally connected to 192.168.2.0/24 or vlan 2 network and there pc should be assigned 192.168.2.0/24 Network IP Range only from R1 or L3 sw DHCP Server. Thanks, Faiz ... View more

   with this above info-  i came to know that "router need a ios only one time when router booting". when router found ios ,although any one deleted or problem in flash card, router never goes to rommon mode until i restart or power off     thanks a lot for your replay.  ... View more

Yes you are right, what happened when this problem came i thought it may be problem in slot0 so that i manually changed to slot1.    i am not sure plz tell me this  one point , Example:-if i erase flash card or problem in flash card, it never gives me error until then i restart the router. Because all my configuration and ios is loaded in ram? but my case router is in rommon mode and flash card is empty, then i restarted the router but same result. so i changed flash card in another slot but same output. And i connected a flash card in my system. card is working and no configuration files (empty) in flash card. ... View more

thank u for reply can u plz tell me which cause that was happend like that because which was running for a long time good condition but suddenly . because as per my knowledge ,when that was good condition all configuration which is loaded in ram from flash card ,until then router restated this problem was not happend ?   ... View more

Hi zeeshna ,     a).  in lan we use a subnet 10.10.16.0/22 means ip range from 10.10.16.1 to 10.10.19.254 .      b) we assgined ips to nodes from 10.10.16.1 to 10.10.18.200.       c)remaining ips means 10.10.18.201 to 10.10.19.254 is assgined to any nodes by manually ,that nodes traffic should be rejected by router     means as far as i know i configure acl using host or network, can i configure acl ips range like to allow 10.10.16.1 to 18.200 by router and remaing ips block.     Thanks,     Faiz ... View more

this is my configuration but no result, MY REQUIRMENT IS I HAVE A TWO CISCO 3560 SWITCH WHICH IS RUNNING HSRP AND EIGRP I need a all vlan 1 devices and users ,if they go to anyware out of lan to interface g1/4 ,they should have a record. i can able to ping my netflow server and all units getting but except it Current configuration : 5693 bytes ! ! Last configuration change at 12:15:59 UTC Thu Jun 13 2013 ! NVRAM config last updated at 12:16:00 UTC Thu Jun 13 2013 ! version 15.0 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname 3560-X-TATA ! boot-start-marker boot-end-marker ! enable secret 5 $1$noPD$12H1OP44QVk6Aj9E7jxbB0 ! username cisco privilege 15 password 0 cisc no aaa new-model clock timezone UTC 5 30 system mtu routing 1500 flow record lab1 match datalink dot1q priority match datalink mac source-address match datalink mac destination-address match ipv4 tos match ipv4 protocol match ipv4 destination address match transport source-port match transport destination-port collect interface input snmp collect interface output snmp collect counter flows collect counter bytes collect counter packets collect timestamp sys-uptime first collect timestamp sys-uptime last ! ! ! flow exporter netflowserver description corpor@teserver destination 10.10.17.166 source Vlan1 dscp 3 transport udp 9996 ! ! flow monitor FLOW-MONITOR-1 record lab1 exporter netflowserver cache timeout active 300 ! ip routing ! interface GigabitEthernet1/4 description COPD_TATA_100MPBS no switchport ip flow ingress ip flow egress ip flow monitor FLOW-MONITOR-1 input ip address 192.168.2.14 255.255.255.252 ! interface Vlan1 ip flow ingress ip flow egress ip flow monitor FLOW-MONITOR-1 input ip address 10.10.50.53 255.255.252.0 standby 10 ip 10.10.50.51 standby 10 priority 200 standby 10 preempt standby 10 track 1 decrement 150 ! router eigrp 500 network 10.10.48.0 0.0.3.255 network 192.168.2.12 0.0.0.3 eigrp stub connected summary ! ip default-gateway 10.10.50.52 ip http server ip http secure-server ip flow-export source Vlan1 ip flow-export destination 10.10.17.166 9996 ! ip route 0.0.0.0 0.0.0.0 192.168.2.13 snmp-server community public RO snmp-server community netflow RW snmp ifmib ifindex persist end 3560-X-TATA#show flow record flow record lab1:   Description:        User defined   No. of users:       1   Total field space:  51 bytes   Fields:     match datalink dot1q priority     match datalink mac source-address     match datalink mac destination-addre     match ipv4 tos     match ipv4 protocol     match ipv4 destination address     match transport source-port     match transport destination-port     collect interface input snmp     collect interface output snmp     collect counter flows     collect counter bytes     collect counter packets     collect timestamp sys-uptime first     collect timestamp sys-uptime last 3560-X-TATA#show flow monitor FLOW-MONITOR-1 Flow Monitor FLOW-MONITOR-1:   Description:       User defined   Flow Record:       lab1   Flow Exporter:     netflowserver   Cache:     Type:              normal     Status:            allocated     Size:              128 entries / 9732 bytes   Cache:     Type:              normal (Platform cache)     Status:            allocated     Size:              Unknown   Timers:                        Local        Global     Inactive Timeout:  15 secs     Active Timeout:    300 secs     1800 secs     Update Timeout:    1800 secs ... View more

thanks for reply,    i have heard that netflow support on latest ios version on 3560-x ... View more