About Santosh Sharma

Santosh Sharma · 09-06-2020

IntroductionIssueSolutionConfigurationImportant Links Introduction ACL to match DVMRP is not supported in NCS5500. This document describes how to use UDF to match DVMRP packets in NCS5500. Issue ACL to match DVMRP packets is not supported in NCS5500...

Santosh Sharma · 04-17-2020

ProblemChallengesSolutionConfigurationVerification Problem RP and FC doesn't reloads incase PLATFORM-CROSSBAR-2-ACCESS_FAILURE is seen. Challenges EEM script can be used to reload RP and FC after detecting the syslog. EEM script in this case can be ...

Santosh Sharma · 03-26-2019

IntroductionMonitoring CPUMonitoring Memory Introduction This document describes the steps to monitor CPU and Memory in NCS5500 device. The examples are from a router having one LC and two RPs: RP/0/RP0/CPU0:leaf-1#show platform Tue Mar 26 14:24:13....

Santosh Sharma · 12-05-2018

ProblemSolutionConfigs required in the NodeSteps to enable the script Problem Double-bit ECC error causes LC reboot as soon as the error is seen, hence we do not have sufficient time to capture all the logs whenever Double-bit ECC error is seen. In ...

Santosh Sharma · 08-18-2018

IntroductionDetailsMore Scripts Introduction EEM script to capture packets at SPP every 15 mins and other logs every minute. Details Following o/ps are captured every minute: show drops all location allsh controllers np counters all location 0/0/cpu...

Santosh Sharma · 02-19-2019

For L2 interface, the pmap configuration can be done in l2transport mode. Following will work: int <> l2transport service-policy input <>

Santosh Sharma · 09-18-2018

There can be issue with file transfer to the router. Lets try copying the pie in the router and check md5. Lets do install add incase md5 is proper

Santosh Sharma · 08-30-2018

Here is more details: RP/0/RSP0/CPU0:ASR9K-Escalation#run # nvgen -c -l 1 -t 1 -o 1 > /disk0:/show_run1 Building configuration...# ls -lrt show_run1-rw-rw-rw- 1 0 0 39211 Aug 31 13:30 show_run1# # nvgen -c -l 1 -t 1 -o 1 ...

Santosh Sharma · 08-30-2018

I dont think we can do it from XR prompt, but we can do it from shell prompt: # nvgen -c -l 1 -t 1 -o 1 > /disk0:/show_run1 Building configuration...# ls -lrt show_run1-rw-rw-rw- 1 0 0 39211 Aug 31 13:30 show_run1#

Santosh Sharma · 08-30-2018

You can try "show run | file disk0:show_run" Thanks, Santosh

Member Since	‎02-11-2014 06:00 AM
Date Last Visited	‎09-15-2023 03:29 AM
Posts	31
Total Helpful Votes Received	106

User Statistics

User Activity

Matching DVMRP packets using ACL(UDF) in NCS5500

EEM script to monitor multiple syslogs and reload RP/FC depending on syslog

NCS5500: CPU and Memory monitoring using SNMP

EEM script to capture logs when Double-bit ECC error is seen

EEM Script to Capture Packet at SPP

Re: L2 ingress policing on NCS5500/NCS540

Re: XR upgrade 5.3.1 -> 6.3.3/6.4.2 fails on "install add" claiming corrupt PIE files

Re: Can we run copy command in Cisco ios xr silently i.e. without user prompt

Re: Can we run copy command in Cisco ios xr silently i.e. without user prompt

Re: Can we run copy command in Cisco ios xr silently i.e. without user prompt