Hello Experts, Hope you are doing well! We have deployed Mesh configuration for site (A) controller 5508 with version 7.6.130.0 Can we have a Mesh AP redundancy with site (B) controller 5508 with version 7.6.130.0 which is over a WAN if, site A controller fails? For indoor APs is it possible to use L3 roaming for the sites APs are deployed as Flex connect mode with local switching & auth? As 7.6.130.0 multi country is not supported for mesh/bridge mode, I have read in 8.0 it is supported is it correct ? Kindly find the image I have tried to put the site view as attachment.   Thanks in advance! Thanks & Regards//       ... View more

Hello Experts, Hope you are doing well!   I am using 5508 controller and couple of sites are used on Flexconnect mode, I want to know if I can configure L3 roaming on the SSID? if, yes how?   Thanks in advance!   ... View more

Hello Experts, Hope all are doing well! 1. In a deployment there were 2600 series AP & now client ordered 1600 series AP. In one floor both the models are deployed, now interesting is 1600 series does not support clean air & 2600 is with clean air will both the AP work smooth in Mixed ? if, no ! if, we disable clean air in 2600 than? 2. I see clients getting ms.. high like more than 10ms - 100ms (TTL) any solution for the same ? Or what are the issue it is caused so that we can try to find out the reason.   Thanks in advance !       ... View more

Hello Experts, I have configured couple of sites with Flexconnect AP. all the sites are working fine and no issues. But I see a strange issue for a new site where I see E.g. I have configured ssid = abc, on the site I see is displayed SSID = (wireless abc) did not understand the reason!! rest all 45 sites are working fine and also the ssid display abc only. Need urgent help!!   Any suggestion or troubleshooting guide will be appreciated. Thanks in advance!   ... View more

Hello Experts, Hope you all are doing well! We have implemented 802.1x everything is working cool, just finding a way to avoid going to all laptop and doing manual setting in the SSID properties. Any method to push the setting automatically in the SSID profile, like selecting peap etc etc? Thanks in advance! Lenka ... View more

Hello Experts, I am facing 2 issues at site, kindly find the questions as below. We have deployed 5508 controller with version - 7.6.130.0 Q1. AIR-LAP1142N-N-K9, as AP get restart the configuration get wiped I have to reconfigure again and again. Any solution or observations?   Q2. AIR-CAP1602I-A-K9 is being deployed in Canada region I checked in the regulatory compliance seems good, however, Radio 1 gets down frequently could not understand Radio 0 works fine but Radio 1 always creates problem. Any solution for the same? kindly find the status it shows for Radio 1 Radio slot#1       Radio Interface Type# 802.11a/n Admin Status # Enable Oper Status # DOWN Regulatory Domain # Not supported   Thank you for all your views in advance!! ... View more

Hello Experts, I am facing 2 issues at site, kindly find the questions as below. We have deployed 5508 controller with version - 7.6.130.0 Q1. AIR-LAP1142N-N-K9, as AP get restart the configuration get wiped I have to reconfigure again and again. Any solution or observations?   Q2. AIR-CAP1602I-A-K9 is being deployed in Canada region I checked in the regulatory compliance seems good, however, Radio 1 gets down frequently could not understand Radio 0 works fine but Radio 1 always creates problem. Any solution for the same? kindly find the status it shows for Radio 1 Radio slot#1       Radio Interface Type# 802.11a/n Admin Status # Enable Oper Status # DOWN Regulatory Domain # Not supported   Thank you for all your views in advance!!     ... View more