About rainnomm56

rainnomm56 · 05-15-2018

I put all my most used helper scripts in "/var/opt/ncs/ext".For services who need those external scripts i make symlink in service python folder. rain@ohoo:/var/opt/ncs/devstuff/hostlist/python/hostlist$ ll lrwxrwxrwx 1 root ncsadmin 16 ma...

rainnomm56 · 05-11-2018

Natural key would port and vlan combination for service port. My issue is that NSO does not allow key used in template for "when" statement. How can i have 2 different xml lines with out it?Live device conf: <epipe> <service-id>3714</serv...

rainnomm56 · 05-06-2018

What is the expected performance of NSO doing sync-from?I have 110 alcatel "alu-sr" devices and sync from them takes quite some time, around 7 minutes. Last device that finished sync was "kjj-sr1".<INFO> 6-May-2018::18:23:57.519 nso ncs[19682]: ncs s...

rainnomm56 · 04-24-2018

Hi,I have not found any good guide how to implement CPE full configuration in NSO. Most of examples are of one service, that is small part of the device configuration. I could do a single monster size cpe_service but that would grow unmanageable pret...

rainnomm56 · 04-23-2018

Hi,What is the correct way of discovering/storing device model parameter? For mpls l3vpn i have 8 different CPE-s from cisco IOS software familiy. Almost all those CPE-s have different uplink configuration. Do I understand correctly that there is no ...

rainnomm56 · 08-30-2024

Cisco CoPP consistency across platforms is quite bad: In IOS you have "drop".On C1100 series IOS-XE routers you can simulate drop by configuring drop to both actions "police 8000 conform-action drop exceed-action drop".On C9200CX they say "The creati...

rainnomm56 · 05-13-2018

In short, if you want to implement such block with when statements, you'd need to have the when condition on a higher level in the hierarchy of the target model (e.g. on 'sap' rather than on 'sap-id'), and you'd need to duplicate the block in your xm...

rainnomm56 · 05-08-2018

Sry for posting before finalizing testing. Initial reconcile of T3 took 10min. Today 6 new services have been configured to "kjj-sr1" and T3 reconcile took ~45sec. That is ok. Of course this is just one device in the service path, but in general this...

rainnomm56 · 05-08-2018

Another question confusing matter. On live ISP network nobody can model from day 1 all the services. Usually you go live with couple most used services and leave some of service in old/manual provisioning. That automatically means that NSO will be ou...

rainnomm56 · 05-07-2018

I did that and in NSO:- config pull is 25sec- then it gives no output, i presume its translating config to xml for 43sec?- then for some reason it is doing second time config pull for 25sec. For second config pull it is not doing translation.That par...

Member Since	‎04-25-2008 10:45 PM
Date Last Visited	‎09-06-2024 04:07 AM
Posts	15
Total Helpful Votes Received	10

User Statistics

User Activity

NSO python3 inheritance error - ImportError: No module named

template - 'when' attribute cannot be used on key elements

sync-from performance

CPE full configuration - how to segment it ?

Device model parameter?

Re: ASR920 Control-Plane Policing: Drop action

Re: template - 'when' attribute cannot be used on key elements

Re: sync-from performance

Re: sync-from performance

Re: sync-from performance