Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About ranjipremandrewp
03-12-2018
Stats
Member since
12-14-2013
93
Posts
10
Helpful
0
Solutions
03-09-2018
03:03 AM
I see this command - Rx 100ms multiplier 5 at their end, so should it be
bfd interval 100 min_rx 500 multiplier 5
... View more
03-08-2018
09:21 AM
Thanks for the reply, on the other hand, I feel 500ms is a bit long interval. (5seconds)
Can I make it to 50ms and ask them to change the same on their end. Will it cause overhead on the network. Just want to know the best interval to be configured in production
... View more
03-08-2018
09:13 AM
My service provider says that he has configured this at his end.
Tx 500ms multiplier 5
Rx 100ms multiplier 5
How do I configure the BFD at my end?
Should it be
bfd interval 500 min_rx 500 multiplier 5
... View more
Labels:
Created by
ranjipremandrew
in Other Network Architecture Subjects
in Other Network Architecture Subjects
01-10-2018
03:27 AM
01-10-2018
03:27 AM
How to remove a primary subnet alone in a interface vlan that has a secondary subnet
Example see below
interface Vlan2 no ip redirects ip address 10.1.1.2/24 ip address 10.1.2.2/24 secondary ip ospf passive-interface ip router ospf 1 area 0.0.0.0 hsrp 2 preempt delay minimum 300 priority 120 ip 10.1.1.1 ip 10.1.2.1 secondary no shutdown
... View more
Labels:
01-05-2017
03:45 AM
I am sorry, but could you please let me know what should be the configuration on the switchports that connect the routers
... View more
01-05-2017
03:17 AM
Suppose there are two routers that run EIGRP and are interconnected by an L2 switch. Is there a way that neighborship can be formed between these routers.If yes, how?
... View more
Labels:
Created by
ranjipremandrew
in Switching
08-23-2016
09:09 AM
08-23-2016
09:09 AM
Just want to understand how is that BPDUs themselves are not getting looped in a layer 2 network where there are redundant links in a network
... View more
- Tags:
- bpdu spanningtree
Labels:
08-18-2016
09:49 AM
We are planning to upgrade from VTP version 2 to version 3. Is downtime required for this change?
Could you please share any document stating the steps of this change. I searched online but couldn't find one.
... View more
- Tags:
- 3750v2 vtpv3
Labels:
Created by
ranjipremandrew
in Switching
08-16-2016
04:57 AM
08-16-2016
04:57 AM
Could you please explain the significance of Destination Service Access Point and Source Service Access Point?
... View more
Labels:
Created by
ranjipremandrew
in Switching
08-09-2016
08:14 AM
08-09-2016
08:14 AM
Could you please advise me if c3750-ipservicesk9-mz.122-50.SE1.bin on WS-C3750V2-48PS would support VTP version 3
Please find the 'show vtp status' result below
VTP Version : running VTP2 Configuration Revision : xx Maximum VLANs supported locally : 1005 Number of existing VLANs : xx VTP Operating Mode : Client VTP Domain Name : xxxxxx VTP Pruning Mode : Disabled VTP V2 Mode : Enabled VTP Traps Generation : Enabled
... View more
- Tags:
- 3750v2 vtpv3
Labels:
08-08-2016
10:17 AM
I did a 'show internal vlan usage' on a N7K and this is what I got.
SW1# show vlan internal usage VLANs DESCRIPTION ------------------- ----------------- 3968-4031 Multicast 4032-4035,4048-4059 Online Diagnostic 4036-4039,4060-4087 ERSPAN 4042 Satellite 3968-4095 Current
Can you please explain the meaning of each usage?
... View more
Labels:
06-16-2016
04:27 AM
I wasn't able to ping the hosts in Packet tracer. Is it possible to ping the hosts when we use real switches and clients?
... View more
06-16-2016
04:22 AM
Thanks for the reply. I had this question in one of the interviews. The interviewer said to configure switchport trunk native vlan 10 on Switch A and then switchport trunk native vlan 20 on Switch B.
I tried what he suggested but I got 'Native vlan mismatch' error messages on the console.
... View more
03-09-2018
I see this command - Rx 100ms multiplier 5 at their end, so should it be
bfd interval 100 min_rx 500...
03-08-2018
Thanks for the reply, on the other hand, I feel 500ms is a bit long
interval. (5seconds) Can I make ...
03-08-2018
My service provider says that he has configured this at his end. Tx
500ms multiplier 5 Rx 100ms mult...
01-10-2018
How to remove a primary subnet alone in a interface vlan that has a
secondary subnet Example see bel...
01-05-2017
I am sorry, but could you please let me know what should be the
configuration on the switchports tha...
01-05-2017
Suppose there are two routers that run EIGRP and are interconnected by
an L2 switch. Is there a way ...
Created by
ranjipremandrewp
in Switching
08-23-2016
08-23-2016
Just want to understand how is that BPDUs themselves are not getting
looped in a layer 2 network whe...
08-18-2016
We are planning to upgrade from VTP version 2 to version 3. Is downtime
required for this change? Co...
Created by
ranjipremandrewp
in Switching
08-16-2016
08-16-2016
Could you please explain the significance of Destination Service Access
Point and Source Service Acc...
08-09-2016
Could you please advise me if c3750-ipservicesk9-mz.122-50.SE1.bin on
WS-C3750V2-48PS would support ...
08-08-2016
I did a 'show internal vlan usage' on a N7K and this is what I got. SW1#
show vlan internal usage VL...
06-16-2016
I wasn't able to ping the hosts in Packet tracer. Is it possible to ping
the hosts when we use real ...
Public Statistics
| Date Registered | 12-14-2013 07:38 PM |
| Date Last Visited | 03-12-2018 05:16 PM |
| Total Messages Posted | 93 |
| Total Helpful Votes Received | 10 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 10 | |
| 10 | |
| 5 | |
| 5 |
.jpg "VIP Expert"){kind=icon}
.jpg "Hall of Fame Guru"){kind=icon}
