Hy Pros. Recently I've added a new local user to the LMS, but everytime he logs in, he gets a white page in his browser. I've tried the workarounds for bug CSCte29226, but they didn't fix it. Do you have any hints? regards Marc ... View more

Hello experts. I'm familiar with SPAN and know about RSPAN, but have never had to configure it. Some new requirements concerning one of our datacenters made me think of using it. But there are lots of questions that have to be answered before we will implement RSPAN within our DC. Most questions have been cleared, but some important ones couldn't been answered by Cisco documents or any forum discussion found by me. Please have a look at the attached picture that'll give you a scheme about the affected DC. We need to capture the traffic of servers1-4 with only one probe connected to a Catalyst 6509 Series device. The idea was to use one RSPAN VLAN on all involved switches interconnected with trunks. - One really difficult question is: How can we prevent Server1s traffic from being populated within the RSPAN VLAN down to the C4948 switches? Or traffic from Server2 over to the switch of Server 4. And so on... - Another interesting point is: Nevertheless we're not 100% sure what the 'reflector-port' might be causing, but this syntax option is not given on any of the involved switches. Does it matter in our case? - Will the traffic received at the C4506 within the defined RSPAN VLAN automatically be populated up to the C6509 without configuring a reflector-port? As you can see there is some confusing about this kind of structure und we have to have a solution quickly. So I would be very glad if some could help me with this topic as soon as possible. Thanks you very much in advance! best regards Marc Wynen ... View more

Hy. Since months we have a problem with our Syslog AA. We're not receiving any E-Mail that should be send as a reaction to received syslog messages. The Syslog Collector is correctly subscribed and resubscription doesn't fix our problem as well as restarting both processes (Collector and Analyser). By using logview at syslog.log I can see that there are permanently messages received and written into the file syslog.log. In Syslog Reports messages can be identified that should have triggered an E-Mail, but no E-Mail was received. The mailserver itself might not be the problem, because we are still receiving E-Mail for Job Status reports. The filter.dat file looks like this: Filters for the server: de0-cwge Mode: DROP Filter expressions: ^((\S+);;;(PIX)(-(\S+))?-(6)(-(302002\s*))\s*:\s*.*)$ ^((\S+);;;(PIX)(-(\S+))?-(6)(-(302001\s*))\s*:\s*.*)$ ^((\S+);;;(PIX)(-(\S+))?-(6)(-(304001\s*))\s*:\s*.*)$ ^((\S+);;;(FW)(-(\S+))?-(6)(-(SESS_AUDIT_TRAIL\s*))\s*:\s*.*)$ ^((\S+);;;(\S+)(-(\S+))?-(7)(-(.*\s*))?\s*:\s*.*)$ ^((\S+);;;(LINK)(-(\S+))?-(3)(-(UPDOWN\s*))\s*:\s*.*)$ ^((\S+);;;(LINEPROTO)(-(\S+))?-(5)(-(UPDOWN\s*))\s*:\s*.*)$ ^((\S+);;;(LINK)(-(\S+))?-(5)(-(CHANGED\s*))\s*:\s*.*)$ ^((\S+);;;(LINK)(-(\S+))?-(5)(-(UPDOWN\s*))\s*:\s*.*)$ ................... So this also doesn't seem to be the cause. Can anybody please help me to find a solution for this? Many thanks in advance! cheers Marc ... View more

Hey Pros. When I try to add WISM cards to the LMS they are not managable. Neither inventories nor configs can be collected. It's telling me "device not reachable". The community strings are correct and by trying "Management Station to Device" it says "ok" to SNMP but SSH is not successful, nevertheless they are accessible via SSH from the LMS server. Any idea how I could fix this? Device updates are all installed. CS 3.3.0 CM 5.2.1 RME 4.3.1 Thanks in advance! cheers Marc ... View more

Hy. If I look at different places in the LMS I can see different counts of devices that are managed. In the device management of CS I get a total count of 1989 devices by selecting all. The same count is listed if I select all devices in RME Report Generator and RME Device Management. This is definitely a good value. But if I look at CM I get only 1945 devices. More worst if I go to CM Reports and select all devices then only 1206 will be selected. Data collection also tells me about 1945 devices. This is strange and I don't understand why. Does anyone have an idea how to fix this? It's really urgent! I have to report the total number of ports but this value will be wrong because not all devices seem to be accessible by CM reports. CS 3.3.0 CM 5.2.1 RME 4.3.1 Thanks in advance! cheers Marc ... View more