About ltodd2

ltodd2 · 11-05-2025

Hi.Trying to setup bridge/mesh between to 1815w APs, one of which is also the ME WLC. Is this possible as im having no luck. Ive tried following a few docs but not managed to get it working. When i change the MAP AP to flex+bridge mode and after a ...

ltodd2 · 10-29-2025

HiWe have been getting failures of 1542i AP for a while but though it was an environment issue but we are getting more and more failing now and some are not in a bad environment. When they fail the switch shows the port down, PoE shows as ieee PD. ...

ltodd2 · 10-10-2025

HiWe are still running an old 5520 wlc and have a few 1542 APs left that we need to use but they have 8.10.130 on them and will not connect and downgrade on our wlc. Ive tried to load an older version and managed to get it to load 8.8.100 and its cu...

ltodd2 · 09-22-2025

HiWe are in the middle of migrating from an old 5520wlc to a 9800. Only a few sites have been migrated so far but we have spotted an issue in prime heatmaps. It seems a random number of AP's will show any kind of coverage on the map while others sh...

ltodd2 · 05-06-2015

HiWe have a new install thats still in learning mode. I have an alert on the DC for one of the sensors saying that s1p1 - s1p4 has no link.We have an active/standby ASA pair behind the sensor. and 2 nexus's in front. One nexus connects to s1p1 and ...

ltodd2 · 11-05-2025

hi @Enes Simnica, thanks for the quick reply. The reason im trying it is to remove some ethernet over power adapters that seem to have just decided to start playing up dropping to 11meg from the 280 they were doing. This mesh idea was my idea of a ...

ltodd2 · 11-05-2025

Hi MarkIm going to take it that there must be some defect in this model as all the ones we have the issues with show the same issues. No led, PoE at Ieee Pd and no console output.

ltodd2 · 11-03-2025

Ive just double checked and the wlc license is all good. On prime prime infra license is good showing its happy, however i did notice under controller license it shows as 0. All license type jobs are running and show as green. not sure if this mean...

ltodd2 · 10-29-2025

Thanks for the quick reply. LLDP is on and ive tried a couple of the APs connected to different switches (models and software) im getting nothing after the boot time. Im assuming they are dead but though worth an ask on here incase there was a known...

ltodd2 · 10-24-2025

Thanks for the reply. Ive just tried and still no joy from all the AP's. all show online and the are all working as its been checked from site. Just prime will not show the heat map for all of them. Just migrated another site the other week which ...

Member Since	‎06-21-2008 05:25 AM
Date Last Visited	‎10-29-2025 10:18 AM
Posts	22
Total Helpful Votes Received	6

User Statistics

User Activity

Mesh setup on Mobility Express and1815w AP not working

1541i APs failing, PoE only no ethernet

trying to downgrade 1542i from 8.8 to 8.5.140

Prime 3.10.4 heatmaps not working correctly

DC shows no link on sensor but I have traffic though one interface

Re: Mesh setup on Mobility Express and1815w AP not working

Re: 1541i APs failing, PoE only no ethernet

Re: Prime 3.10.4 heatmaps not working correctly

Re: 1541i APs failing, PoE only no ethernet

Re: Prime 3.10.4 heatmaps not working correctly