About malhotra_suneet

malhotra_suneet · 03-11-2020

My existing setup has a ASA SM on 6500 which is EOL.I now have a Firepower4120s pair with ASA instances on it. What is the best method to migrate ? Can we use Migration tool in this case ? Or should I configure from the scratch for the new devices.....

malhotra_suneet · 02-12-2020

FIRPOWER 4120Cisco Adaptive Security Appliance Software Version 9.8(4)Firepower Extensible Operating System Version 2.2(2.53)Device Manager Version 7.8(2) I am currently working on ASA migration from a ASA-Service Module on 6500 to Firepower 4100I ha...

malhotra_suneet · 01-24-2020

HI have a ASA instance on a Firepower 4420 device.I have defined Eth1/1 as the management interface with ip address 10.80.80.5 255.255.255.0 and default gateway as 10.80.80.1 config !interface Ethernet1/1management-onlynameif managementsecurity-leve...

malhotra_suneet · 01-15-2020

HiI am replacing a moduler Cisco SVC-ASA-SM1 which is installed on my Cisco 6500 switch, replacing with a Firepower 4120 model (Next generation Firewall), is there any tool to migrate it ? GUI ? Or everything needs to be done on CLI from the scratch ...

malhotra_suneet · 05-17-2019

I have a pair of ASR9Ks, under M-LAG group (de-clustered), and have 2 stack of Cat9000 series switches dual-homed to ASR9K,Can I have a server/switch under the extisitng setup with a port-channel configured on it and each physical link in the port-ch...

malhotra_suneet · 02-17-2020

@Marvin Rhoads wrote:The only time clustering tends to make sense is when you have throughput requirements that exceed what you can get with single appliances. Your ASA on 4120 is already going to have many multiples of the throughput the ASASM had....

malhotra_suneet · 02-13-2020

Thank you Marvin for the quick response. The information is very helpful.

malhotra_suneet · 01-24-2020

dug a little bit and found that the fxos is showing interface eth1/1 as down, not sure whyFirepower-4120-Lab-A(fxos)# show interfaceEthernet1/1 is down (Link not connected)Dedicated InterfaceHardware: 1000/10000 Ethernet, address: 00fd.2270.b65c (bia...

malhotra_suneet · 01-24-2020

If I remove the cable I still see ASA eth1/1 as up up and that is because it is a logical instance of ASA on physical Firepower box, and interface mapping is being done. The problem still remains,

malhotra_suneet · 01-16-2020

Thanks for the quick reply, here is some of the details of the device hardware/inventory and software version,Am I good to use the Migration Tool in this case ? Source DeviceName: "module 3", DESCR: "WS-SVC-ASASM-1 Adaptive Security Appliance Service...

Member Since	‎05-09-2018 05:50 AM
Date Last Visited	‎04-22-2020 12:29 AM
Posts	15

User Statistics

User Activity

Migrating from ASA SM to ASA Instance on Firepower

FIrepower with ASA Instance - Cluster vs HA Failover

Unable to ping gateway from ASA instance

Cisco ASA to Firepower Migration

Can I have 2 cat swithes under 2 Racks of ASR9K (delustered) M-LAG and then a server beneath the switch on a port-channel. Will the 2 cat switches work under a single MC lag group ?

Re: FIrepower with ASA Instance - Cluster vs HA Failover

Re: FIrepower with ASA Instance - Cluster vs HA Failover

Re: Unable to ping gateway from ASA instance

Re: Unable to ping gateway from ASA instance

Re: Cisco ASA to Firepower Migration