Hi Guys, We have the same issue with our SG500 Series-PoE-Switches and one SG300. Acessing the Web-Management via IP is working but not via FQDN. Even if EOS is announced and active, this issue should be fixed by Cisco. BR Florian
... View more
Dear Community, we're observing a very interesting problem with IP-Phones connected to a SG350x-24p stack using LLDP-MED. Problemdescription: Almost everytime we connect or restart a new IP-Phone (Mitel MiVoice 69x0 with actual Firmware 5.x) to our 2-member SG350x-24P Stack (FW 2.5.0.90) the Master-Switch reboots. Errorlog: 03-Dec-2019 16:57:59 :%STCK SYSL-A-UNITMSG: UNIT ID 1,Msg:%AUTOSMARTPORT-F-DEV_CALC_FAILED: XDP device type calculation failed: interface gi2/0/20 - capability 3 ***** FATAL ERROR ***** Reporting Task: BRMN. Software Version: 2.5.0.90 (date Sep 26 2019 time 16:12:12) base_address=0xb4684000 ros(+0x78ac20)[0xb4e0ec20] ros(HOSTG_fatal_error+0x10)[0xb4e11224] ros(OSSYSG_fatal_error+0x2a0)[0xb53dbce4] ros(+0xb598c0)[0xb51dd8c0] ros(+0xd710f8)[0xb53f50f8] ros(+0xde6904)[0xb546a904] ros(+0xde0418)[0xb5464418] ros(+0xded5a8)[0xb54715a8] ros(+0xdf1dc4)[0xb5475dc4] ros(+0xc883a8)[0xb530c3a8] /lib/libp2linux.so.1(task_run+0xf4)[0xb4614818] ####################################################### 04-Dec-2019 17:33:51 %AUTOSMARTPORT-F-DEV_CALC_FAILED: XDP device type calculation failed: interface gi2/0/19 - capability 3 ***** FATAL ERROR ***** Reporting Task: BRMN. Software Version: 2.5.0.90 (date Sep 26 2019 time 16:12:12) base_address=0xb4681000 ros(+0x78ac20)[0xb4e0bc20] ros(HOSTG_fatal_error+0x10)[0xb4e0e224] ros(OSSYSG_fatal_error+0x2a0)[0xb53d8ce4] ros(+0xb598c0)[0xb51da8c0] ros(+0xd710f8)[0xb53f20f8] ros(+0xde6904)[0xb5467904] ros(+0xde0418)[0xb5461418] ros(+0xded5a8)[0xb546e5a8] ros(+0xdf1dc4)[0xb5472dc4] ros(+0xc883a8)[0xb53093a8] /lib/libp2linux.so.1(task_run+0xf4)[0xb4611818] ***** END OF FATAL ERROR ***** ^^ this event was logged before the last reboot. I first tought, it depends on a not completly deactivated smartport-configuration. So I deaktivated everything concerning smartports. Global Config: macro auto disabled no macro auto processing cdp no macro auto processing lldp macro auto processing type host disabled macro auto processing type ip_phone disabled macro auto processing type ip_phone_desktop disabled macro auto processing type switch disabled macro auto processing type ap disabled Interface config: no macro auto smartport no macro auto persistent But these settings did not work. The reboots still persist. So I disabled LLDP globally - the reboots went away, but our phones didn't get the Right voice vlan via LLDP-MED and all other LLDP devices were not shown anymore. So I decided to implement the following workaround: I re-enabled LLDP globally, but disabled LLDP receive on the voice enabled (oui enabled) switchports. Meanwhile we now distribute the VLAN Information via DHCP. Our voice config now on an Access-Switch-Stack (one port exampe): voice vlan id 910 voice vlan state oui-enabled voice vlan oui-table add 08000f Mitel_IPphones interface vlan 810 name Clients interface vlan 910 name VoIP interface GigabitEthernet2/0/20 storm-control broadcast level 1 spanning-tree portfast spanning-tree guard root switchport mode general switchport general allowed vlan add 810 untagged switchport general pvid 810 no lldp receive voice vlan enable ! As far as I found out, this bug last quite a long time in the Firmware of Small-Business-Switches. We hope, that this issue will be solved soon. Otherwise, LLDP-MED is not usable for voice vlans. You'll find an open bug under: CSCvq71611 I didn't check, if the bug persists under SG500-stacks and SG550x-stacks. Best regards, Florian (CCDP, CCNP R+S, CCNA wireless, CCNA Collaboration)
... View more
Hi, we have the same issue on a 350x stack. As far as I figuered out It really depends on LLDP-MED and OUI voice vlan. Everytime we reboot a phone, one of the stack members (mostly the master device) reboots. 04-Dec-2019 17:33:51 %AUTOSMARTPORT-F-DEV_CALC_FAILED: XDP device type calculation failed: interface gi2/0/19 - capability 3 ***** FATAL ERROR ***** Reporting Task: BRMN. Software Version: 2.5.0.90 (date Sep 26 2019 time 16:12:12) base_address=0xb4681000 ros(+0x78ac20)[0xb4e0bc20] ros(HOSTG_fatal_error+0x10)[0xb4e0e224] ros(OSSYSG_fatal_error+0x2a0)[0xb53d8ce4] ros(+0xb598c0)[0xb51da8c0] ros(+0xd710f8)[0xb53f20f8] ros(+0xde6904)[0xb5467904] ros(+0xde0418)[0xb5461418] ros(+0xded5a8)[0xb546e5a8] ros(+0xdf1dc4)[0xb5472dc4] ros(+0xc883a8)[0xb53093a8] /lib/libp2linux.so.1(task_run+0xf4)[0xb4611818] ***** END OF FATAL ERROR ***** There's already a bug-report and assigned number: CSCvq71611 https://quickview.cloudapps.cisco.com/quickview/bug/CSCvq71611 We have this issue with new Mitel IP Phones 6920 and 6930. Best regards, Florian (CCNP+CCDP)
... View more
