Hi, using a C1921 with ehwic-4esg as internet router. Using pppoe connection across build-in gigabit port to ISP and svi vlan1 to route traffic to firewalls. pppoe connection works fine (can ping the internet, etc) but svi is not routing any traffic. See below config.   Interface vlan1 is using "IP unnumbered dialer 1". Also tried "ip address pool IAS" but didn't make any difference. IOS version 15.4(3)M3. Any help will be appreciated... Thanks, Rico. ==================================== ! hostname rtr01 ! ip dhcp pool IAS  import all  origin ipcp  dns-server 194.151.228.18 194.151.228.34 ! ip cef multilink bundle-name authenticated ! cts logging verbose ! redundancy ! no cdp run ! policy-map custom-shaper-30Mbps  class class-default   shape average 28800000 ! interface Embedded-Service-Engine0/0  no ip address  shutdown ! interface GigabitEthernet0/0  description ISP CPE  no ip address  load-interval 30  duplex full  speed 100  pppoe enable group global  pppoe-client dial-pool-number 1  service-policy output custom-shaper-30Mbps ! interface GigabitEthernet0/1  no ip address  shutdown  duplex auto  speed auto ! interface GigabitEthernet0/0/0  no ip address ! interface GigabitEthernet0/0/1  no ip address ! interface GigabitEthernet0/0/2  no ip address ! interface GigabitEthernet0/0/3  no ip address ! interface Vlan1  ip unnumbered Dialer1  ip verify unicast reverse-path  ip tcp adjust-mss 1452  load-interval 30 ! interface Dialer1  description Customer Traffic PPPoE Connection  ip address negotiated  ip verify unicast reverse-path  encapsulation ppp  mtu 1492  dialer pool 1  dialer-group 1  ppp pap sent-username <removed> password <removed>  ppp ipcp mask request  ppp ipcp address accept ! ip forward-protocol nd ! ip route 0.0.0.0 0.0.0.0 Dialer1 ! dialer-list 1 protocol ip permit ! ========================================================================= rtr01#sh vlan-switch VLAN Name                             Status    Ports ---- -------------------------------- --------- ------------------------------- 1    default                          active    Gi0/0/0, Gi0/0/1, Gi0/0/2, Gi0/0/3 1002 fddi-default                     act/unsup 1003 token-ring-default               act/unsup 1004 fddinet-default                  act/unsup 1005 trnet-default                    act/unsup VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1    enet  100001     1500  -      -      -        -    -        1002   1003 1002 fddi  101002     1500  -      -      -        -    -        1      1003 1003 tr    101003     1500  1005   0      -        -    srb      1      1002 1004 fdnet 101004     1500  -      -      1        ibm  -        0      0   1005 trnet 101005     1500  -      -      1        ibm  -        0      0   ========================================================================== rtr01#sh int status Port    Name               Status       Vlan       Duplex Speed Type Gi0/0/0                    connected    1          a-full  a-1000 10/100BaseTX/1000BaseT Gi0/0/1                    connected    1          a-full  a-1000 10/100BaseTX/1000BaseT Gi0/0/2                    connected    1          a-full   a-100 10/100BaseTX/1000BaseT Gi0/0/3                    notconnect   1            auto    auto 10/100BaseTX/1000BaseT ... View more

Can anyody help with the following: I use an IP Trade system connected to CUCM version 6.1.2. For this, an IP Trade turret is an advanced SIP phone configured on the CUCM. At CUCM I have configured a H.323 gateway with PSTN access. Also in this setup I have an IP Trade TPO server that serves as a RTP mixer for join functions on the IP Trade turrets. the problem I have is this: When a call is active between PSTN phone (through H.323 gateway) and SIP turret1,  and SIP turret2 wants to join this call, the design within the IP Trade system moves the active call from PSTN to turret1 to the TPO server. this is the flow: Call is active between PSTN and turret1. turret2 wants to join this call. Turret2 sends a SIP INVITE to the TPO server. TPO server sends a SIP INVITE to turret1. Turret1 sends a SIP INVITE to CUCM. all SIP INVITE messages indicate the new destination for the call --> TPO server.TPO server will mix all the streams making a 'conference' the problem is this: the CUCM receives the SIP INVITE from turret1 and has to update the PSTN caller (H.323 call). this is not happening! CUCM does not send any updates to H.323 gateway for change of destination.  this is the error in the tracelog of CUCM: 000010464| 2009/12/08 13:55:23.477|  001| SdlError  | H245SessionEstablishedFailure         |  NA                            | H245Interface(1,100,156,7)      |  H245SessionManager(1,100,25,7)  | (1,100,25,7).1-(*:192.168.20.251)       |  Destination process does not  exist Is this a process that is not supported by CUCM?   I read alot about H.323 not supporting redirection in an active call.. anybody any info on this issue? help would be appriciated, although also a TAC case has been opened for this. Thanks, Eduard. ... View more