Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Bauer Chris
03-14-2019
Bauer Chris
Member since
11-10-2010
Beginner
6
Posts
0
Helpful
0
Solutions
07-10-2012
07:31 AM
I have seen conflicting information regarding downtime for this upgrade process and still have questions after reading http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/configuration/guide/issu_efsu.html#wp1095791 . In this scenario, we have a VSS with one SUP in each chassis. Are the chassis or modules rebooted one at a time? For instance, if I issue an "issu loadversion", will this just load the code on the SUP in the standby chassis, or will it load the code on the modules as well? If it does load the code on the modules, then I will have to wait the longest time from the "show issue outage slot all" before issuing a "issu runversion", correct? Also, what outage times have people seeen on modules that support pre-loading? I have not been able to find any documented information on this other than it is faster, and the link referenced above still shows a 5 minutes outage for a warm reset on one of the modules. Any information is appreciated Thanks -Chris
... View more
Labels:
06-27-2012
03:03 PM
Hello I have been looking for information on the failover time for a redundant interface. In particular, I am looking at configuring an ASA with two physical interfaces to different routers in a ring running EIGRP. I understand there will be the EIGRP reconvergence time, but I am wondering how this compares to failing over to a standby node with a single attached interface. Has anyone had any experiences with this type of failover in a similar situation? Thanks -Chris
... View more
Labels:
11-10-2010
01:48 PM
I was able to get this working, but it appears I will have to declare each remote network in the access list and pay attention to the ordering. Here is what worked. distribute-list eigrpACL_FR out interface inside was added to the EIRGP config, and the access list reads as follows - access-list eigrpACL_FR standard permit 10.1.0.0 255.255.255.0 access-list eigrpACL_FR standard deny any Not what I had hoped for, but it works. Thanks for the assistance!
... View more
11-10-2010
01:38 PM
I attempted to do this, but adding a filter for 0.0.0.0 matches all routes causing all of my statics inserted via RRI to be blocked. It looks like a route-map may be the only way to do this, and even then I have not been able to get this working.
... View more
11-10-2010
11:10 AM
I did try a distribute list and a route map, but was unable to get the syntax correct. Any advice on how I could set this up is appreciated. Thanks!
... View more
11-10-2010
09:48 AM
Hello I am trying to configure a new ASA ( Version 8.3(2) ) with EIGRP enabled on the inside interface along with RRI. However, I do not want to redistribute or listen for a default route. I have verified the config below prevents the ASA from learning default route should the outside interface go down, but it is still redistributing itself as a potential default gateway. Is it possible to prevent this? router eigrp 2801 no auto-summary no default-information in no default-information out network 131.183.0.0 255.255.0.0 passive-interface default no passive-interface inside redistribute static Thank you
... View more
Labels:
07-10-2012 07:31 AM
I have seen conflicting information regarding downtime for this upgrade
process and still have quest...
06-27-2012 03:03 PM
HelloI have been looking for information on the failover time for a
redundant interface. In particul...
11-10-2010 01:48 PM
I was able to get this working, but it appears I will have to declare
each remote network in the acc...
11-10-2010 01:38 PM
I attempted to do this, but adding a filter for 0.0.0.0 matches all
routes causing all of my statics...
11-10-2010 11:10 AM
I did try a distribute list and a route map, but was unable to get the
syntax correct. Any advice on...
Public Statistics
| Date Registered | 11-10-2010 09:33 AM |
| Date Last Visited | 03-14-2019 02:08 PM |
| Total Messages Posted | 6 |
