Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About NISSA_2
Stats
Member since
02-01-2010
8
Posts
0
Helpful
0
Solutions
Created by
NISSA_2
in Small Business Routers
in Small Business Routers
07-12-2010
12:16 PM
07-12-2010
12:16 PM
I got the QuickVPN working with Windows 7 Enterprise 32-bit terminating to a Cisco SA520 . The Quick VPN looked like it was going to connect, said Verifying, then failed with an error message that " Remote gateway is not responding". I had disabled Windows firewall and re-enabled it. The IKE service mentioned was already set to automatic.
... View more
Created by
NISSA_2
in Small Business Security
in Small Business Security
07-12-2010
10:19 AM
07-12-2010
10:19 AM
I have two customers with this same issue. Was a fix released? We cannot resolve by allowing unsigned active x controls and adding to trusted sites. I've tried setting the security level to low but that doesn't work either. Both SA520's are running 1.1.42.
... View more
05-28-2010
07:18 AM
We have 20-25 extensions running on it. I cleaned up the config a little prior to posting it.
... View more
05-27-2010
06:06 PM
I've attached configurations for a UC520 phone system and Cisco ASA 5510 firewall where the system is colo'd at a data center and no users connect directly to the phone system over the LAN. Summary Points: The Cisco UC520 phone system sits in a data center with a 10Mbps Internet feed. All users on this phone system are remote users connecting with Cisco IP Communicators and Cisco SPA-525G phones. Every user on the system connects their PC, laptop, or SPA525G phone by first initiating an SSL VPN connection. The SSL VPN sessions terminate on a Cisco ASA 5510 firewall The Cisco ASA 5510 firewall was used to terminate SSL VPN sessions to get around the limit of 10 VPN tunnels on the UC520. Purchased a 25-user SSL VPN license for the ASA. No users are located at the data center where the system resides.
... View more
Labels:
03-27-2010
08:36 PM
Thank you. That fixed the issue I was having. Apparently the SPA525G phone works regardless of the CFNA timeout being set lower than the hunt group timeout, however, the hunt group final destination didn't work with the CIPC phones unless the CFNA was higher than the hunt group timeout as you indicated.
... View more
03-18-2010
03:26 PM
I have a workaround, but not a resolution. If I set the timeout on the hunt-group to 9 or less, the final destination is dialed. A timeout of 10 or above, with a CIPC client added to the hunt-group, prevents the final destination from being dialed. I have tried with Cisco IPSec VPN client and a Cisco SSL VPN client and have the same behavior with both. The VPN sessions terminate to a Cisco ASA 5510 firewall.
... View more
03-17-2010
12:20 PM
In the example below on a UC520, if I add any extension such as 110 which uses an IP Communicator phone, all the extensions ring, but the final destination will not be dialed and the call goes silent but remains connected. If I remove 110 (CIPC phone), or if I have the user close their CIPC, the final destination is dialed. I've confirmed this behavior by adding and removing three different CIPC phone extensions to three different voice hunt-groups. Any idea why hunt groups fail with the addition of a CIPC phone to it? voice hunt-group 1 parallel final 913125551212 list 102,105,110 timeout 16 pilot 511 ephone-dn 16 dual-line number 110 no-reg primary label 110 description Dave Sutton name Dave Sutton call-forward busy 399 call-forward noan 399 timeout 10 corlist incoming user-uscallsonly translation-profile incoming CallBlocking ephone 7 device-security-mode none video mac-address 0024.1DD9.3454 ephone-template 16 max-calls-per-button 2 username "asmith" password 123 type CIPC button 1:16
... View more
Labels:
02-02-2010
12:00 PM
I have a UC520 phone system and need to support more than 10 teleworkers with SPA525G phones. The phones connect via SSL VPN to the UC520 fine, but I'm having difficulty connecting the SPA525G phone with SSL VPN to an ASA5510 firewall. Has anyone been able to make this work?
... View more
Labels:
Created by
NISSA_2
in Small Business Routers
07-12-2010
07-12-2010
I got the QuickVPN working with Windows 7 Enterprise 32-bit terminating
to a Cisco SA520. The QuickV...
07-12-2010
I have two customers with this same issue. Was a fix released? We cannot
resolve by allowing unsigne...
Created by
NISSA_2
in Voice Systems
05-28-2010
05-28-2010
We have 20-25 extensions running on it. I cleaned up the config a little
prior to posting it.
Created by
NISSA_2
in Voice Systems
05-27-2010
05-27-2010
I've attached configurations for a UC520 phone system and Cisco ASA 5510
firewall where the system i...
Created by
NISSA_2
in Voice Systems
03-27-2010
03-27-2010
Thank you. That fixed the issue I was having. Apparently the SPA525G
phone works regardless of the C...
Created by
NISSA_2
in Voice Systems
03-18-2010
03-18-2010
I have a workaround, but not a resolution. If I set the timeout on the
hunt-group to 9 or less, the ...
Created by
NISSA_2
in Voice Systems
03-17-2010
03-17-2010
In the example below on a UC520, if I add any extension such as 110
which uses an IP Communicator ph...
Public Statistics
| Date Registered | 02-01-2010 09:34 PM |
| Date Last Visited | 08-18-2017 03:53 AM |
| Total Messages Posted | 8 |
