em 02-15-2013 09:36 AM
Olá a todos,
Tenho uma conexão ISDN E1 e os seguintes dial peers configurados no gateway:
dial-peer voice 1 pots
translation-profile incoming DID-STRIP
direct-inward-dial
port 0/0/0:15
!
dial-peer voice 201 voip
destination-pattern 9.......
session protocol sipv2
session target ipv4:10.0.0.127
session transport udp
voice-class codec 1
dtmf-relay rtp-nte
ip qos dscp cs3 signaling
no vad
No entanto, as chamadas vindas da PSTN através do link E1 falham:
Oct 9 14:43:38 UTC: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0DF4
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98397
Exclusive, Channel 15
Facility i = 0x9F8B0100A10F02010B06072A8648CE1500040A0100
Protocol Profile = Networking Extensions
0xA10F02010B06072A8648CE1500040A0100
Component = Invoke component
Invoke Id = 11
Operation = InformationFollowing (calling_name)
Name information in subsequent FACILITY message
Calling Party Number i = 0x2183, '1128038030'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, '2129381100'
Plan:ISDN, Type:National
Oct 9 14:43:38 UTC: ISDN Se0/0/0:15 Q931: Received SETUP callref = 0x8DF4 callID = 0x114A switch = primary-ni interface = User
Oct 9 14:43:38 UTC: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Calling Number=1128038030, Called Number=2129381100, Voice-Interface=0x49504F40,
Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE,
Peer Info Type=DIALPEER_INFO_SPEECH
Oct 9 14:43:38 UTC: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Result=NO_MATCH(-1) After All Match Rules Attempt
Oct 9 14:43:38 UTC: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:
dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=-1
Oct 9 14:43:38 UTC: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Calling Number=1128038030, Called Number=2129381100, Voice-Interface=0x0,
Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE,
Peer Info Type=DIALPEER_INFO_FAX
Oct 9 14:43:38 UTC: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Result=NO_MATCH(-1) After All Match Rules Attempt
Oct 9 14:43:38 UTC: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:
dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=-1
Oct 9 14:43:38 UTC: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Calling Number=1128038030, Called Number=2129381100, Voice-Interface=0x0,
Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE,
Peer Info Type=DIALPEER_INFO_SPEECH
Oct 9 14:43:38 UTC: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Result=NO_MATCH(-1) After All Match Rules Attempt
Oct 9 14:43:38 UTC: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:
dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=-1
Oct 9 14:43:38 UTC: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8DF4
Cause i = 0x809C - Invalid number format (incomplete number)
Alguma ideia do que pode estar causando a falha?
Agradeço desde já.
Solucionado! Ir para a Solução.
em 02-15-2013 04:13 PM
Ola Christopher,
Parece que o a chamada entrante não encontra nenhum dial-peer como candidato para combinar com o número discado.
Se vc deseja que a chamada entre pela interface E1, no dial-peer 1 sugiro configurar um dos critérios utilizados pelo gateway para recebê-la, por exemplo:
dial-peer voice 1
incoming called-number .
Do contrário, o dial-peer permanecerá desativado.
Aplique algum dos critérios como no exemplo e verifique se funciona.
Um abraço,
em 02-17-2013 03:09 PM
Ola Christopher,
Em adição as dicas do André, de uma olhada neste documento para um melhor entendimento de como um dial-peer de entrada é selecionado.
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml
Att
Leonardo Santana
em 02-15-2013 04:13 PM
Ola Christopher,
Parece que o a chamada entrante não encontra nenhum dial-peer como candidato para combinar com o número discado.
Se vc deseja que a chamada entre pela interface E1, no dial-peer 1 sugiro configurar um dos critérios utilizados pelo gateway para recebê-la, por exemplo:
dial-peer voice 1
incoming called-number .
Do contrário, o dial-peer permanecerá desativado.
Aplique algum dos critérios como no exemplo e verifique se funciona.
Um abraço,
em 02-17-2013 03:09 PM
Ola Christopher,
Em adição as dicas do André, de uma olhada neste documento para um melhor entendimento de como um dial-peer de entrada é selecionado.
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml
Att
Leonardo Santana
em 02-18-2013 05:17 AM
Muito obrigado pessoal pelos esclarecimentos.
No entanto ainda fica confuso para mim, pois o documento também afirma:
Voice-port (associated with the incoming call setup request) with configured dial peer port (applicable for inbound POTS call legs)
If no match is found in the step 3, the router or gateway attempts to match the configured dial peer port to the voice-port associated with the incoming call. If multiple dial peers have the same port configured, the dial peer first added in the configuration is matched.
O que me levaria a acreditar que o match seria dado mesmo na porta configurada (port 0/0/0:15) neste caso de dial peer pots.
De toda maneira obrigado, funcionou com as dicas dadas.
Abraços
em 02-19-2013 07:18 AM
Tem certa razão Christopher.
Complementando o documento que o Leonardo forneceu (+5), segue:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml#topic11
Destination-pattern is configured and a voice-port or session target is also configured.
Você pode até verificar o estado de operação do dial peer antes e depois de configurar algum dos 3 critérios indicados no documento, com o comando 'show dial-peer voice summary'.
Um abraço
Descubra e salve suas ideias favoritas. Volte para ver respostas de especialistas, passo a passo, tópicos recentes e muito mais.
Novo por aqui? Comece com estas dicas. Como usar a Comunidade Guia do novo membro
Navegue pelos links rápidos da Comunidade e usufrua de um conteúdo personalizado e em seu idioma nativo: