buen dia,
tengo un problema para configurar las conferencias en ccme, estoy trabajando con la version 12.4(24)T de IOS y la 7.1 de ccme, estuve revisando varios ejemplos de configuracion pero el problema es que no me acepta los comandos. esta es la salida del show inventory
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V07 , SN: FTX1345A07C
NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 0", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V01 , SN: FOC10351G13
NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V03 , SN: FOC134830FY
NAME: "PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with one DSP"
PID: PVDM2-16 , VID: V01 , SN: FOC13381K3M
NAME: "PVDMII DSP SIMM with one DSP with half channel capcity on Slot 0 SubSlot 5", DESCR: "PVDMII DSP SIMM with one DSP with half channel capcity"
PID: PVDM2-8 , VID: V01 , SN: FOC11441JEA
NAME: "AIM Service Engine 1", DESCR: "AIM Service Engine"
PID: AIM-CUE , VID: V03 , SN: FOC12166CK9
NAME: "High Density Voice on Slot 1", DESCR: "High Density Voice"
PID: , VID: 1.1, SN: JAD070702M0
NAME: "E1 (1 Port) Multi-Flex Trunk WAN Daughter Card on Slot 1 SubSlot 0", DESCR: "E1 (1 Port) Multi-Flex Trunk WAN Daughter Card"
PID: VWIC-1MFT-E1= , VID: 1.0, SN: 30452099
NAME: "PVDM 3-C549 Simm on Slot 1 SubSlot 1", DESCR: "PVDM 3-C549 Simm"
PID: PVDM-12= , VID: , SN:
NAME: "PVDM 3-C549 Simm on Slot 1 SubSlot 2", DESCR: "PVDM 3-C549 Simm"
PID: PVDM-12= , VID: , SN:
NAME: "PVDM 3-C549 Simm on Slot 1 SubSlot 3", DESCR: "PVDM 3-C549 Simm"
PID: PVDM-12= , VID: , SN:
los comandos que quiero aplicar, de acuerdo a las guias de configuracion son los siguientes
sccp local GigabitEthernet0/0
sccp ccm 10.15.15.1 identifier 1 version 7.0 ------------------------> No lo acepta solo me deja colocar el comando sccp ccm 192.168.20.253 priority 1
!
!
sccp ccm group 1 --------------------------------------> NO lo acepta
associate ccm 1 priority 1
associate profile 101 register confer1
associate profile 103 register xcode1
!
!
dspfarm profile 103 transcode ---------------------------> NO lo acepta
codec g711ulaw
codec g711alaw
codec g729r8
maximum sessions 6
associate application SCCP
!
dspfarm profile 101 conference ---------------------------> NO lo acepta
codec g711ulaw
codec g711alaw
codec g729r8
maximum sessions 5
associate application SCCP
!
Alguien me puede indicar por que no me acepta los comandos y que debo hacer para poder configurar las conferencias.
de antemano gracias.
