el 06-07-2012 11:25 AM
Estimados Señores,
Favor, ayudar con éste problema...!
¿Cómo puedo convertir un Access Point modelo AIR-AP1262N-A-K9 (AP Independiente) al protocolo LWAPP?,
LWAPP es el protocolo Lightweight Access Point Protocol (LWAPP) todo esto para que un Wireless LAN Controller AIR-WLC2106-K9-V05 lo pueda reconocer en la red a este Access Point, ya sea;conectado directamente al WLC (2106) o a la red vía Switch 2950 de Cisco.
Por lo que se hasta ahora hay una versión de Firmware 12.4 (23c) JA5 que se debe descargar de Cisco e instalarla en el AP-1262, ya que; la que trae es la 12.4 (25.d) JA1.
Pero no puedo descargar dicho Firmware ni tampoco el procedimiento de instalación de la posterior imagen.
Atte.
Pablo Brintrup
PD.: Por favor, ayudar en esto, desde ante mano mil gracias a todos
el 06-08-2012 06:10 AM
el 09-28-2018 06:41 PM
hola tengo un AIR-LAP1262N-A-K9 y no me deja hacer nada con el no puedo poner los codigos normales ni me deja actualizarlo. por favor si sabes como darle solucion a mi problema dejame los pasos para lograr poder hacer q mi equipo funcione.. mira aqui y dame una solucion por favor
r WRDTR,CLKTR: 0x8200083f 0x40000000
r RQDC ,RFDC : 0x80000033 0x00000217
using eeprom values
WRDTR,CLKTR: 0x8200083f 0x40000000
RQDC ,RFDC : 0x80000033 0x00000217
using MCNG ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
......................................................................................................................................................................................................................................................
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x8200083f, 0x40000000
RQDC, RFDC : 0x80000033, 0x00000217
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
64bit PCIE devices
PCIEx: initialization done
flashfs[0]: 74 files, 15 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31739904
flashfs[0]: Bytes used: 19011072
flashfs[0]: Bytes available: 12728832
flashfs[0]: flashfs fsck took 13 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 30:e4:db:82:69:96
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/ap3g1-k9w8-mx.153-3.JA10/ap3g1-k9w8-mx.153-3.JA10"...###############
File "flash:/ap3g1-k9w8-mx.153-3.JA10/ap3g1-k9w8-mx.153-3.JA10" uncompressed and installed, entry point: 0x4000
executing...
enet halted
IOS Secondary Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
......................................................................................................................................................................................................................................................
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x8200083f, 0x40000000
RQDC, RFDC : 0x80000033, 0x00000217
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
Radio 0 : Vendor 0x11AB, Device 0x8350
64bit PCIE devices
Radio 1 : Vendor 0x11AB, Device 0x8324
PCIEx: initialization done
flashfs[0]: 74 files, 15 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31739904
flashfs[0]: Bytes used: 19011072
flashfs[0]: Bytes available: 12728832
flashfs[0]: flashfs fsck took 14 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 30:e4:db:82:69:96
Creating Test Kernel diagnostic commands
Radio 0 : Vendor 0x11AB, Device 0x8324
Radio 1 : Vendor 0x11AB, Device 0x8350
Radio 2 : Vendor 0x26B7, Device 0x963F
Radio 3 : Vendor 0xC369, Device 0x1009
******** AUTOMATIC DDR CALIBRATION UPGRADE LOGIC *********
=== 1. Is original FCS bootloader in BS:? If not, skip upgrade ===
---> original FCS bootloader not detected -- skip upgrade
Unable to locate IOS image with name **xx**.
Boot CMD: 'boot flash:/ap3g1-k9w8-mx.153-3.JA10/ap3g1-k9w8-xx.153-3.JA10'
Loading "flash:/ap3g1-k9w8-mx.153-3.JA10/ap3g1-k9w8-xx.153-3.JA10"...###################################
File "flash:/ap3g1-k9w8-mx.153-3.JA10/ap3g1-k9w8-xx.153-3.JA10" uncompressed and installed, entry point: 0x100000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1260 Software (AP3G1-K9W8-M), Version 15.3(3)JA10, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Tue 23-Aug-16 01:30 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
......................................................................................................................................................................................................................................................
flashfs[2]: 74 files, 15 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31481856
flashfs[2]: Bytes used: 19011072
flashfs[2]: Bytes available: 12470784
flashfs[2]: flashfs fsck took 12 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 1 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCC
Copy in progress...CCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
Radio0 present 8364B 8000 B8020000 0 B8030000 10
Rate table has 300 entries (16 legacy/64 11n/220 11ac)
POWER TABLE FILENAME = ram:/D2.bin
Radio1 present 8364B 8000 B0020000 0 B0030000 C
POWER TABLE FILENAME = ram:/D5.bin
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco AIR-LAP1262N-A-K9 (PowerPC460exr) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FTX1528E4SY
PowerPC460exr CPU at 666Mhz, revision number 0x18A8
Last reset from power-on
LWAPP image version 8.0.140.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 30:E4:DB:82:69:96
Part Number : 73-12175-05
PCA Assembly Number : 800-32268-05
PCA Revision Number : A0
PCB Serial Number : FOC15250NQL
Top Assembly Part Number : 800-33866-01
Top Assembly Serial Number : FTX1528E4SY
Top Revision Number : A0
Product/Model Number : AIR-LAP1262N-A-K9
% Please define a domain-name first.
Press RETURN to get started!
el 09-29-2018 09:22 PM
Hola.
Que pasas despues de que te pide presionar "Enter"?
Descubra y salve sus notas favoritas. Vuelva a encontrar las respuestas de los expertos, guías paso a paso, temas recientes y mucho más.
¿Es nuevo por aquí? Empiece con estos tips. Cómo usar la comunidad Guía para nuevos miembros
Navegue y encuentre contenido personalizado de la comunidad