求助，SPA-1XCHSTM1/OC3

[aya_weib]

SPA-1XCHSTM1/OC3 板卡插在GSR设备 12000-SIP-601 板卡上，显示状态为status is out of service
无从下手，该板块在其他 gsr设备上状态是好的。
#show diags 14
SLOT 14 (RP/LC 14): Modular SPA Interface Card (10G)
MAIN: type 149, 68-3106-03 rev B0
Deviation: 0
HW config: 0x60 SW key: 00-00-00
PCA: 73-10465-07 rev B0 ver 4
Design Release 1.0 S/N SAD131701FK
MBUS: Embedded Agent
Test hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00
DIAG: Test count: 0x00000000 Test results: 0x00000000
FRU: Linecard/Module: 12000-SIP-601=
Processor Memory: MEM-LC5-2048=(Non-Replaceable)
Packet Memory: MEM-LC5-PKT-512=(Non-Replaceable)
L3 Engine: 5 - ISE 10 Gbps
MBUS Agent Software version 2.72 (RAM) (ROM version is 3.70)
ROM Monitor version 255.255
Fabric Downloader version used 4.1 (ROM version is 4.1)
Primary clock is CSC 0
Board is analyzed
Board State is Line Card Enabled (IOS RUN )
Insertion time: 00:00:28 (5y7w ago)
Processor Memory size: 2147483648 bytes
TX Packet Memory size: 268435456 bytes, Packet Memory pagesize: 32768 bytes
RX Packet Memory size: 268435456 bytes, Packet Memory pagesize: 32768 bytes
0 crashes since restart
SPA Information:
subslot 14/0: SPA-10X1GE-V2 (0x508), status is ok
subslot 14/1: SPA-1XCHSTM1/OC3 (0x463), status is out of service
subslot 14/2: Empty
subslot 14/3: Empty
High Speed SPA allowed in subslot 14/2 and 14/3: No

[one-time]

感谢您的提问！稍后会有小伙伴为您解答的！

[jingjian]

有没有比较两台GSR的软件版本，12000-SIP-601= 是10G的带宽，而且支持2：1的负载，同时支持这两块SPA是没有问题的。
可以尝试更换到14/2这个槽位上

[aya_weib]

arvinjing 发表于 2017-3-21 11:05
有没有比较两台GSR的软件版本，12000-SIP-601= 是10G的带宽，而且支持2：1的负载，同时支持这两块SPA是没有 ...

软件版本不同。
状态好的这台是
show version
Cisco Internetwork Operating System Software
IOS (tm) GS Software (GSR-K3P-M), Version 12.0(32)SY8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by cisco Systems, Inc.
Compiled Fri 13-Feb-09 01:34 by leccese
Image text-base: 0x50010F48, data-base: 0x54D815A0
ROM: System Bootstrap, Version 11.2(20030108:132517) [jkuzma-112 2.2] RELEASE SOFTWARE
BOOTLDR: GS Software (GSR-K3P-M), Version 12.0(32)SY8, RELEASE SOFTWARE (fc1)
状态不好的这台是：
show version
Cisco Internetwork Operating System Software
IOS (tm) GS Software (C12KPRP-K3P-M), Version 12.0(32)SY13, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by cisco Systems, Inc.
Compiled Mon 14-Mar-11 04:18 by vpernank
Image text-base: 0x00010000, data-base: 0x056D3000
ROM: System Bootstrap, Version 12.0(20051020:160303) [sjabbar-CSCsa64979_4 1.17dev(0.5)] DEVELOPMENT SOFTWARE
BOOTLDR: GS Software (C12KPRP-K3P-M), Version 12.0(32)SY13, RELEASE SOFTWARE (fc3)
但问题spa应该会自动同步固件版本的吧！在状态好的那台gsr上，插上子卡后显示为
SLOT 2:00:01:48: %SPA_OIR-6-INSCARD: Card inserted in Subslot 0
SLOT 2:00:01:51: %SPA_PLUGIN-6-SPI4_SYNC: SPA-1XCHSTM1/OC3[2/0]: SPI4 bus synchronization achieved.
SLOT 2:00:01:55: %SPA_PLUGIN-6-FIRMWARE_DOWNLOADING: SPA-1XCHSTM1/OC3[2/0]: Downloading SPA firmware (bundled)...via shared memory.
SLOT 2:00:01:59: %SPA_PLUGIN-6-FIRMWARE_APPS_DOWNLOADING: SPA-1XCHSTM1/OC3[2/0]: Downloading SPA firmware application (bundled)...vi
a shared memory.
SLOT 2:00:02:19: %SPA_PLUGIN-6-EFC_SYNC: SPA-1XCHSTM1/OC3[2/0]: EFC bus synchronization achieved.
00:50:46: %SPA_OIR-6-ONLINECARD: SPA (SPA-1XCHSTM1/OC3) online in subslot 2/0
然后就绿灯了。

[aya_weib]

状态不好的那台GSR插上板卡后的信息当时现场没获取下来

[aya_weib]

14/2没试过，插在14/3上还是一样故障。