03-08-2010 06:40 AM
I am trying to configure ACE 4710 bridge mode and I am stuck up in physical interface configuration. I have configured gig1/2 of ACE as trunk port and on layer 2 switch I have assigned that interface (gig1/2) to VLAN 11. I tried trunk port also but it got disabled due to BPDU error.
I am not able to ping servers as well as gateway. Below are the topology and context configuration:
Router (vlan 13: IP 172.16.11.254)
|
ACE (int gig1/2)
|
L2 Switch
|
Servers (vlan 11: IP 172.16.11.1 and 11.2)
Admin Context
===========
resource-class rc1
limit-resource all minimum 0.00 maximum unlimited
limit-resource sticky minimum 0.20 maximum unlimited
boot system image:c4710ace-mz.A3_2_4.bin
interface gigabitEthernet 1/1
switchport access vlan 1000
no shutdown
interface gigabitEthernet 1/2
switchport trunk allowed vlan 11,13
no shutdown
interface gigabitEthernet 1/3
shutdown
interface gigabitEthernet 1/4
shutdown
access-list ALL line 8 extended permit ip any any
access-list everyone line 8 extended permit ip any any
access-list everyone line 16 extended permit icmp any any
class-map type management match-any remote_access
2 match protocol xml-https any
3 match protocol icmp any
4 match protocol telnet any
5 match protocol ssh any
6 match protocol http any
7 match protocol https any
8 match protocol snmp any
policy-map type management first-match remote_mgmt_allow_policy
class remote_access
permit
interface vlan 1000
ip address 172.16.16.16 255.255.255.0
access-group input ALL
service-policy input remote_mgmt_allow_policy
no shutdown
ip route 0.0.0.0 0.0.0.0 172.16.16.254
context test
allocate-interface vlan 11
allocate-interface vlan 13
member rc1
test Context
=========
access-list bpdu-fixup ethertype permit bpdu
access-list ALL line 8 extended permit ip any any
access-list ALL line 16 extended permit icmp any any
rserver host srv1
ip address 172.16.11.1
inservice
rserver host srv2
ip address 172.16.11.2
inservice
serverfarm host srv
rserver srv1
inservice
rserver srv2
inservice
sticky ip-netmask 255.255.255.255 address both SG1
timeout 120
serverfarm srv
class-map type management match-any remote-mgmt
201 match protocol snmp any
202 match protocol ssh any
203 match protocol icmp any
204 match protocol http any
205 match protocol https any
206 match protocol xml-https any
class-map match-all slb-vip
2 match virtual-address 172.16.11.10 any
policy-map type management first-match remote-mgmt
class remote-mgmt
permit
policy-map type loadbalance first-match slb
class class-default
sticky-serverfarm SG1
policy-map multi-match client-vips
class slb-vip
loadbalance vip inservice
loadbalance policy slb
loadbalance vip icmp-reply
interface vlan 11
bridge-group 1
access-group input bpdu-fixup
access-group input ALL
access-group output ALL
no shutdown
interface vlan 13
bridge-group 1
access-group input bpdu-fixup
access-group input ALL
access-group output ALL
service-policy input remote-mgmt
service-policy input client-vips
no shutdown
interface bvi 1
ip address 172.16.11.9 255.255.255.0
no shutdown
ip route 0.0.0.0 0.0.0.0 172.16.11.254
Could you pls. suggest where I am doing wrong?
Thanks,
Pawan
03-08-2010 11:57 PM
" I tried trunk port also but it got disabled" <----- if your L2 config is not correct, nothing will work.
What is the setup on the switch ? Trunk or access vlan ?
What is the status of the interface ? up ? down ?
Do you see something in your arp table ?
Gilles.
03-09-2010 01:40 AM
I configured that port as trunk port and it's working now after I disabled BPDUguard.
Thanks,
Pawan
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide