Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Is there a way to tailor how long syslog entries are retained in the Monitor Events tab in ANM 3.0? We now have over 1.7M of entries and it takes 4 or 5 minutes to display the entries.
We're running ACE SM and seeing all the VIP addresses, NAT addresses and alias addresses in the ARP table below being assigned the same virtual MAC address. How then would a packet find the correct source/destination if all these MAC addresses are t...
I've been doing a dig on historical posts relating to WAAS deployed through firewalls.I am working on a deployment with Juniper Netscreens & ASA5520 sitting between WAE's. IP connectivity is fine. I can ssh to remote device etc. but users cannot logi...
I have configured the ACE 4710 as a network load balancer and this is working well for most sites. Now I have installed the SSL cert and the https version of the site will not be displayed. Ran Wireshark protocol analyser and it indicates a RST pac...
Hi,I have problem to do and preposition on hidden share.Using 4.1.5.c and not using CIFS - Use Legacy WAFS transport mode:Userid and password is ok.Root is cifs://server/share$/Browse see only non hidden share.Any sugestion what the problem is?Jan
DearsCan anyone help us simulate the values with the reports created by WAASWe received the following values from our provider, for a site they see83.82Gig received and 99.49Gig send, so total of 183.31gig over the linewhen we make a monthly report f...
we did not received response from NAT ip address configured on interface vlan in one context, however, in another context with similar configuration the ping is sucessfully received. the only difference we have observed is that in the context without...
Hi,I have configured normal ACE 4710 in bridge mode and I have statically natted ACE VIP in firewall. But when I am doing FTP to ACE natted IP from outside network I can connect to any of the virtual server but when I run "ls", directly listing is no...
Hi all,I managed to succesfully setup wccp redirection towards an ACNS device for HTTP caching.I am redirecting only 1 address.The problem is the following:the server guys have setup multiple web sites on the same physical server, like:http://server1...
I'm in the process of adding a new accelerator into our setup, today we use WAAS-4.1.5-b25 software version, but the "new" hardware have 4.1.3b.I would like to just upgrade the new hardware to the same version we have in our setup, but cant find the ...
Hi, we have a pair of servers that are load balanced for port 80 traffic to 198.x.x.21 using the h_www_tcp:80 content rule . I recently got a request that port 80 traffic directed to 198.x.x.21/apps/auction be directed only to one of the load balance...
Is it possible to route requests from one ACE appliance to another ACE?One ACE would be just responsible for forwarding client request to another ACE and that ACE would do actual load balancing and then reply back the requests from different sources ...
Dear all experts,I have two CSSs 11150 and have configured them as following:CSS-1#circuit VLAN100 ip address 172.10.10.101 255.255.255.0 ip virtual-router 1 priority 105 preempt ip redundant-vip 1 172.10.10.1 ip critical-service 1 up_dow...
When we select standard mode for the failure detection, the time is typical 60s before the GSS detects that a failure has occured. Does it mean 60s to be a min. failure detection time? If the GSS puts the answer resource offline, how can GSS cons...
Hi,we have an issue in our CSM, even that we have persistence configured, we are not able to mantain it.We are using a version 4.2(3) with supervisor with a version 12.2(18)SXF1.Here it's the configuration of the vserver that we are not able to manta...
