Is this possible with ACE?I'm trying to pass source address info through an imaginary realserver (a proxy). The real server is either configured on a secod ACE and/or on SMTP-proxy server.SS
ACE is load balancing on layer three devices. When trying to traceroute behind ACE does not showing any hop except ACE. traceroute 58.27.191.17 source 192.168.25.6Type escape sequence to abort.Tracing the route to 58.27.191.17 1 192.168.25.137 0 mse...
Hi,Our ACE is configured in One-ARM Mode. I have Oracle Serverfarm been loadbalanced by ACE from where traceroute to ACE is not happening. Oracle Server in VLAN 10 with Gateway configured at Core Switch: 10.10.10.21VLAN 60: 10.10.60.21 in Core switch...
Gurus, I have a setup for transparent caching with my SP client and as of now we are using leastconn as predictor with A2(1.3) as the version.here are my pain points:1. The Cache guys tell me the moment we turn normalization ON the caches cant FTP ...
Is it possible to loadbalance servers located in multiple VLANs using the CSM? I have a need to loadbalance sites the may be located in different VLANs/Subnets but I am unable to consolidate them into a single subnet.
Hi,I deployed 2x6500 and 3xWAE in a branch. Problem is when I set wccp on - all traffic is cut off for the interface with service 61. I've ACL considering traffic which have to be redirected but there is no any match in this ACL. Each WAE is connecte...
Hi,There is WAAS demo we are doing for one of our clients,The whole set up appears to be working ok,From the central manager its evident that there is compresion/optimization.The problem however is that the client is using ping results as a benchmark...
Hi,Do you know if ACE supports dynamic routing like OSPF or is there some new software version that we have to upgrade or a new code to install on the ACEThanks
At present I have a design that will use individual SSL cert per domain and link both certs to (two or one) serverfarm.policy-map multi-match popvip_01 class POP_VIP01 loadbalance vip inservice loadbalance policy POP-POp3_PMT or popPMT1 lo...
We are running a couple of WAAS boxes over the WAN. now the software version is 4.1.1dIt's quite often we get major alarm says "Kernel Crash files and / or User Core files detected ", and most of time it comes from WAAS box which nobody change any se...
Hello all,I have a quick question. How does the ACE 4710 Appliance works with VLAN tagging? I have virtual servers that I am trying to configure behind ACE. The VMs support VLAN tagging. Can I just trunk to link to my core switch and allow the ACE vl...
Hi,I got a alarm tfo limit. I have installed more memory, aknoledge the alarm but at the CM/manage device still showing the alarm. What more a have to do to get rid of this alarm?obrigadoRafaelgc
Hi,We have eazy vpn setup from almost 50 branches to our HO . Now we are going to introduce WAAS , we have few servers connected in the DMZ zone of the ASA ((ASA is directly connected to ACE(6504-E ACE bundle), as shown in the diag)) here ACE is conf...
Hello, Nice, I call Rodolpho and I'm from Brazil. Sorry if my English is bad. I wonder whether WAAS will work in topology with my GRE tunnels without problems, because I have over 20 offices with tunnels reaching in my datacenter by MPLS network. NM ...
Hi all,If I use the probe of a serverfarm, in another serverfarm as a second probe (or logic), the probe randomly fails in the second serverfarm, but works in the first. It does not matter what kind of probes I use. I have tried http, and tcp probes....
