Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
We have a CSM w/ 4.1.6 and would like our RIPS to be able to access a VIP on the same CSM they are on the same subnet but different vlans in L2 design. Any ideas to make this work?
Preparing to deploy CSS11506 in router mode. Is it better to disable spanning-tree on the CSS and enable portfast on both switch and CSS? I think that will have better startup or failover time. Anyone has insight or any pitfall should be avoid? What'...
Hi Guys,I recently swapped my CSS intallation from bridged to routed as I was adding a secondary CSS for redundancy. I have set up NAT using services and groups to allow connection direct to the devices on there old IP's so I don't have to change all...
Hi,I need to know how much time a CSM sent an Offline status for a VIP (vserver) to the GSS via KAL-AP. In other words, I want to see how match time a specific VIP reported a load = 255 to the GSS, because all real servers in the farm were unavailabl...
Hello,I need one of You help me to complete these idea, We have two site, one primary with address 10.0.2.25 and other remote to backup with address 10.2.3.25I need to develop a monitor on primary site, that detect a fail to connect at 10.0.2.25 and ...
Hi All, We have 2 CSS11503s acting iun active/passive using VIP redundancy We found that the passive device rebooted and this was not initiated by anyone. Is there a means to check the reason for the reboot?????. Thanks
my customer use the ISS software to scan the CSS11501. The scan report shows a weakness named "HttpTraceEnabled". how do I to solve the problem? thanks !by the way, the CSS software version is 7.5
Hello, gentlemen. I have a question regarding CSM v4.2(3) in bridge mode and utilizing sticky connection. Do I need to configure a unique non-SSL sticky group for each vserver or can I reuse the same sticky group for multiple vservers? I found a coup...
I'm installing a new CSM with SSL module (WS-X6066-SLB-S-K9) and can't get the debugs to work. Acutally, I enabled debugging (to troubleshoot SSL Handshake problems) but nothing shows up on the screen or in the log. Any ideas?************************...
Hello Giles, i was reading conver in the forum regarding GSLB..is GSLB only failover for servers? few days back we raised a question to our isp to provide us BGP failover. they too mentioned abt gslb but i wasnt convinced. wht we want ISP 1---site 1-...
Hi all.I have a couple of questions with regard to configuring the CSS and would welcome some assistance.Firstly the CSS has multiple servers on a subnet that provide different services. The VIP addresses are also on the same subnet.The clients are o...
Hi all,This morning all the probes went down on the csm module for exactly 15 mins and then came back up. There has been nothing else in the logs to indicate whey the went down. I have found a watchdog process which i think might have started back up...
HelloI am trying to keep a session sticky for 20 mins based on cookies. The problem is the application is using HTTP POSTs and the balance method only looks into the HTTP GET. How can I get the CSS to look into the HTTP POST?Any examples would be gre...
Hi,I have recently upgraded one of our pixes from 6.3 (4) to 7.2(1) the unit is a 515UR with 128MB memory.However since I have upgraded I have notices that the CPU usage has ramped up contatntly around 25% and sometimes around 40% for a consiserable ...
Hello,There's an example at Cisco.com how to provide a Direct Access to Real Servers behind CSM module, and I have to configure the same but with CSS which is different in configuration.I'm using CSS11501 for LDAP load-balancing, there are just two s...
