05-25-2011 05:47 AM
Hi,
I have CSS CSS11501 which is working fine in single arm deployment. Now I want to have
redudency so that in case the switch 1 where CSS is currenlty connected is down.
I can reach the CSS through the second switch 2.
Both the switch are trunk with each other and CSS has one port connected with Switch 2.
Please let me how to configure and achieve that or is it possible to have dual network connection.
Also my local username and password is not showing encrypted.
ENOCDC-CSS01# show run
!Generated on 05/25/2011 16:41:16
!Active version: sg0730106
configure
!*************************** GLOBAL ***************************
username net des-password cisco123 superuser
no restrict web-mgmt
console authentication primary none
virtual authentication primary tacacs
virtual authentication secondary local
idle timeout 15
prelogin-banner "CSSBanner"
logging subsystem flowmgr level debug-7
logging disk log.log
logging subsystem security level debug-7
logging subsystem netman level info-6
host ENOCDC-CSS01 192.168.200.10
no tacacs-server send-full-command
tacacs-server account config
tacacs-server key egntosc
tacacs-server 192.168.10.9 49 5 egntosc
ftp-record enoc 192.168.210.125 bluecoat des-password system99$
ip route 0.0.0.0 0.0.0.0 192.168.200.1 1
!************************* INTERFACE *************************
interface e1
phy 100Mbits-FD
bridge port-fast enable
bridge vlan 2
interface e2
bridge vlan 2
bridge port-fast enable
phy 100Mbits-FD
interface e4
bridge port-fast enable
phy 100Mbits-FD
interface e7
trunk
vlan 3
vlan 200
vlan 205
interface e8
bridge port-fast enable
phy 100Mbits-FD
!************************** CIRCUIT **************************
circuit VLAN3
ip address 192.168.210.10 255.255.255.0
circuit VLAN200
ip address 192.168.200.10 255.255.255.0
circuit VLAN205
ip address 192.168.205.9 255.255.255.0
!************************** SERVICE **************************
service CITRIX_ACCESS_GW_1
ip address 192.168.210.152
keepalive type tcp
keepalive port 443
active
service CITRIX_ACCESS_GW_2
ip address 192.168.210.153
keepalive type tcp
keepalive port 443
active
service CITRIX_XPENAPP_1
ip address 192.168.210.55
keepalive type tcp
keepalive port 80
active
service CITRIX_XPENAPP_2
ip address 192.168.210.56
keepalive type tcp
keepalive port 80
active
service ENOC_EFAX_1
ip address 192.168.200.66
keepalive type none
active
service ENOC_EFAX_2
ip address 192.168.200.67
keepalive type none
active
05-26-2011 07:35 AM
Hi,
Can anyone help me out on this and let me know how can i achieve network level redudency in CSS. I want to connect my single CSS with two switch to provide redundency.
Also I have connected to Core switch gigabit port. But I am getting packet drop and errors on the interfaces.
CORE02#show interfaces gigabitEthernet 2/7
GigabitEthernet2/7 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is 001c.5848.d18e (bia 001c.5848.d18e)
Description: ****connected to the ****Cisco CONTENT SWITCH 192.168.200.10 (GIG 0/7)*****
MTU 1500 bytes, BW 100000 Kbit, DLY 10 usec,
reliability 255/255, txload 10/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s
input flow-control is off, output flow-control is off
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters 02:32:11
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 5
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 7000 bits/sec, 14 packets/sec
5 minute output rate 3935000 bits/sec, 1463 packets/sec
136900 packets input, 9238925 bytes, 0 no buffer
Received 29406 broadcasts (27390 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
14299714 packets output, 5081225730 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
===========================================================================================
ENOCDC-CSS01# sh interface e7
Name ifIndex Type Oper Admin Last Change
---- ------- ---- ---- ----- -----------
e7 9 fe Up Enable 05/26/2011 15:48:12
ENOCDC-CSS01#
ENOCDC-CSS01# show running-config interface e7
!************************* INTERFACE *************************
interface e7
trunk
description "CONNECTED TO CORE_2_PORT_2/7"
vlan 3
vlan 200
vlan 205
===============================================================================================
ENOCDC-CSS01# show ether-errors e7
Ethernet Errors for
Alignment: 0 Internal Rx Errors: 0
FCS: 0 Frame too Long: 0
Single Collision: 3 Carrier Sense Errors 2
Multiple Collisions: 2 Internal Tx Errors: 0
SQE Test: 0 Excessive Collisions 0
Deferred Tx: 5 Late Collisions: 0
==============================================================================================
Please let me know how to fix the redudency and interfaces errors.
Waiting for the reply.
05-27-2011 08:55 AM
Hi,
Can anyone help me out.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide