12-15-2010 04:43 AM
Hi,
I have communications problem between two reservers on different vlans in different bridge groups, but the SAME context. I'm running the ACE in bridged-mode and I have 2 static default routes
Any help would be appreciated
Tyrone
12-15-2010 05:51 AM
Are you able to post your configuration?
12-15-2010 06:19 AM
Here's the interface configuration for the context I'm having a problem with.
interface vlan 87
description BGVLAN87
bridge-group 887
mac-sticky enable
access-group input BPDU
service-policy input LBIFS01
service-policy input LBOAS01
service-policy input LBINTRA
service-policy input LBNWP
no shutdown
interface vlan 501
description BGVLAN501
bridge-group 801
no normalization
mac-sticky enable
access-group input BPDU
service-policy input LBSAP
no shutdown
interface vlan 801
bridge-group 801
mac-sticky enable
access-group input BPDU
access-group input IP_TRAFFIC
no shutdown
interface vlan 887
description BGVLAN87
bridge-group 887
mac-sticky enable
access-group input BPDU
access-group input IP_TRAFFIC
no shutdown
interface bvi 801
ip address 192.165.90.249 255.255.255.0
alias 192.165.90.250 255.255.255.0
peer ip address 192.165.90.251 255.255.255.0
no shutdown
interface bvi 887
ip address 194.132.92.119 255.255.255.192
alias 194.132.92.121 255.255.255.192
peer ip address 194.132.92.120 255.255.255.192
description BGVLAN87
no shutdown
ip route 0.0.0.0 0.0.0.0 192.165.90.254
ip route 0.0.0.0 0.0.0.0 194.132.92.65
12-15-2010 06:22 AM
Can you send the ACL and the output of the routing table ?
What are the two IP addresses of your servers ?
12-15-2010 06:34 AM
access-list IP_TRAFFIC line 8 extended permit ip any any
sho ip route
Destination Gateway Interface Flags
------------------------------------------------------------------------
0.0.0.0 192.165.90.254 vlan501 SE [0x4c]
0.0.0.0 194.132.92.65 vlan87 SE [0x4c]
192.165.90.0/24 0.0.0.0 bvi801 IA [0x30]
194.132.92.64/26 0.0.0.0 bvi887 IA [0x30]
rserver host TEST01
ip address 194.132.92.114
inservice
rserver host saxceap1
ip address 192.165.90.42
inservice
12-15-2010 06:41 AM
what is the default gateway defined on the servers ? Can you ping the rservers from the ACE ? Is arp table populated correctly ?
12-15-2010 06:46 AM
rserservers have gatewys 192.165.90.254 and 194.132.92.65 respec
tively.
Ping rservers from ACE work arp is populated properly!
Tyrone
12-15-2010 06:59 AM
just a guess, but can you put your access-list on the other 2 vlans
too? actually you have traffic going out of your ace and coming back in.
12-15-2010 07:09 AM
I can't
apply the same access-list on the interface
Error: An access-list of the same type has been already activated on the interface
Tyrone
12-15-2010 07:35 AM
yes because you already have the access-list BPDU attached. so change the
access-list BPDU or remove it and attach the other one.
01-05-2011 12:39 AM
The BPDU access-list is there to allow incoming BPDU's I don't think it will be a good idea to remove that.
Has anyone ever seen this problem before??
Can anyone send me an example of a working config in bridged-mode 2 rservers in the same context on different vlans and are able to ping each other????
Tyrone
12-15-2010 06:17 AM
error
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide