cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
986
Views
5
Helpful
2
Replies

unable to find reduction traffic on wave 694 and finding host flapping on switch which is connected to the wave.

nagaprasad123
Level 1
Level 1

Hi Team

I was stuck in a issue with cisco wave-694.

4506 ==========================Wave-694

4506   ( Gi4/40, Gi4/41 )  are in port channel has connected to Wave-694. which is in production suddenly am finding Host flapping on both interfaces

00:06:51: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:06:52: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:06:54: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:06:56: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:06:58: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:07:00: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:07:02: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:07:04: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:07:06: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:07:08: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

in wave-694

aa.png

here we are unable to find reduction %  traffic.

Please  let us know how to overcome this..  and send me a doc for troubleshooting WAAS device.

Appriciate your response as early possiable.

2 Replies 2

Hi,

Can you set any one of interface as primary in 694 device and assign it to standby inerface  group.

ex:

interface Standby 1

ip address XXXX

exit

!

interface GigabitEthernet 1/0

standby 1 primary

exit

interface GigabitEthernet 2/0

standby 1

exit

Regards,

Bala

Hi Team

we are unable to find optimizing traffic and reduction traffic in cisco wave-694, it is in production suddently its not showing. am new for this box, can you please guide me some commands, so i can  copy here for furthere troubleshoot.

sh version

Cisco Wide Area Application Services Software (WAAS)

Copyright (c) 1999-2013 by Cisco Systems, Inc.

Cisco Wide Area Application Services (universal-k9) Software Release 5.0.3c (build b7 Feb  8 2013)

Version: oe694-5.0.3c.7

if there is any bugs also please let me know, please take this in high priritoy  and help me out on this.

111.png

Thanks in advance.

Naga

Review Cisco Networking for a $25 gift card