waas inline and exchange cluster

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-10-2011 10:35 AM
Hello,
Somebody can help me ?
I put an WAE574 in inline mode betwen the switch and the wan router.
When i no shut the inline group, the ip virtual address of the exchange cluster is not OK but the two physical address are OK.
The exchange cluster is on the LAN
When I shut the inline group, all it's OK
Thanks for your help
Bibian
- Labels:
-
Application Networking
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-10-2011 10:54 AM
Hi Bibian,
can you please check and confirm if Exchange is using NLB and has a MCAST MAC address? If yes, i have an answer for you. Thank you.
Ahsan

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-10-2011 10:57 AM
yes
Envoyé à partir de mon Windows® phone.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-10-2011 11:03 AM
What version of WAAS Software you are running? Check this Enhancement request for WAAS
Ahsan

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-10-2011 11:04 AM
4.3.3
Envoyé à partir de mon Windows® phone.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-10-2011 11:20 AM
We would need more data to analyze this issue, Please open a TAC case so this issue can be properly investigated. Thanks.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-10-2011 11:30 AM
Thank's for your help,
I check your informations tomorow with my customer.
If its need I open a case but it for a try and buy solution.
Regards
Bibian
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-10-2011 11:40 AM
Hi Bibian,
I would take packet capture for this issue first so we have some data to analyze, for Try and Buy you should contact WAAS PDI HelpDesk or your Cisco SE so you can get timly support. Let me know if you get no where with this and i can also analyze packet captures for you. Thank you.
Ahsan

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-11-2011 09:23 AM
Hi Ahsan
I thinks its a lan issue
When I check the switch setup I see a mistake on vlan 1 the primary address is not the default gateway.
Tomorow, customer and its provider change this configuration and I make a new test.
You can see on the slide the PB.
If you have got an other Idea It's OK for me
I also ask the SE and I wait answer.
Thank for your help
Bibian
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-02-2011 10:20 AM
Hello Bibian,
We have the same problem with NLB architecture. Finally, you can fixed it?
Thanks,
Best regards,
Jorge M.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-03-2011 01:51 AM
Hello Jorge,
Not the for moment.
I wait a new meeting with the customer to do some new test.
If I fixe my problem I post a response in this forum
Regards
Bibian

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-06-2011 05:37 AM
Hello,
I finally fix my problem
I configure a static mac address on the router and a static arp.
the mac address is the cluster mac address and the arp is the ip and mac address of the cluster :
