01-31-2018 08:05 AM - edited 03-20-2019 09:52 PM
Hello,
I have been looking for the ASA software asa963-20-smp-k8.bin.
On the download page I can only see asa963-1-smp-k8.bin
Can anyone supply the correct url or location for download?
regards,
Brian
*** Sorry for the post, I have located the file***
Solved! Go to Solution.
01-31-2018 10:01 AM
No prob, please mark Helpful and Solved! Then prepare for the upgrade!
01-31-2018 09:11 AM
Hey Brian,
Did you have to open a TAC case to locate the file? I have some 5515-X in production, and none of the fixed software referenced here are available on the download page.
kyler
01-31-2018 09:39 AM - edited 01-31-2018 09:39 AM
Be sure too look at the Interim Releases, see screen shot below.
01-31-2018 09:39 AM
That's where they're hiding! Thanks Tim, I appreciate it.
kyler
01-31-2018 10:01 AM
No prob, please mark Helpful and Solved! Then prepare for the upgrade!
01-31-2018 10:27 AM
Thanks for the screen shot Tim.
01-31-2018 06:52 PM
But 9.6(4) is available so why not use it? As per 9.6(3)20 RN:
"Important: These images were not fully regression tested. Each individual fix was unit tested, and the image has had a limited amount of automated regression testing to confirm a baseline of functionality. Keep this testing status in mind if you decide to run them in a production environment. We strongly encourage you to upgrade to a fully tested Maintenance or Feature release when it becomes available.
Revision: Version 9.6(3)20 – 11/28/2017"
01-31-2018 07:09 PM
Why not just use 9.6(4)? In my environment we need to do extensive reviews of known & fixed bugs, new features , changes to commands and parameters before Amy upgrade like that. Even if it’s as simple as 9.6(3) to 9.6(4).
The interim releases only fix a few bugs, they are more like a patch than an upgrade.
Tim
01-31-2018 07:43 PM
I didn't think staying in the same code branch of 9.6 (from 3 to 4) would be an "upgrade" but I get what you are saying. I think my experience is getting burnt by people/past admins just leaving Interim releases and never going to the next MR/FR. Just out of curiosity you mention "your environment", are you running multiple context?
Also leave this also to confusing documentation and RN by Cisco as on the 9.6 RN they state:
"Version 9.6(3) was removed from Cisco.com due to bug CSCvd78303."
02-01-2018 10:25 AM
@JazzyJ wrote:
Just out of curiosity you mention "your environment", are you running multiple context?
Also leave this also to confusing documentation and RN by Cisco as on the 9.6 RN they state:
"Version 9.6(3) was removed from Cisco.com due to bug CSCvd78303."
Specifically, 9.6(3) was removed, in its place is 9.6(3.1).
I don't run multiple context on the FW that terminates my VPN sessions. When my org purchased these ASAs, site to site VPN or Remote Access VPN was not supported on ASA that ran multiple context. Since then I believe S2S has been added and RA has been added if you have the expensive AC licenses.
HTH
Tim
01-31-2018 06:49 PM
Why not go to 9.6(4) which is a full release not interium? It shows as known fixed on the list below:
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: