Seeing a similar issue on 9300: (Is this related to same bug CSCvq65075 ?)
Model: C9300L-24UXG-4X
Version: 17.03.05
SW Image: CAT9K_IOSXE
802.3bt mode enabled on switch:
cisco9300(config)#hw-module switch 1 upoe-plus
!!!WARNING!!!This Configuration will powercycle the switch to make it effective.Would you like to continue y/n?[confirm]
Building configuration...
[OK]
cisco9300(config)#
cisco9300#show switch detail
Switch/Stack Mac Address : dc0b.0965.7480 - Local Mac Address
Mac persistency wait time: Indefinite
H/W Current
Switch# Role Mac Address Priority Version State
-------------------------------------------------------------------------------------
*1 Active dc0b.0965.7480 1 V02 Ready
Stack Port Status Neighbors
Switch# Port 1 Port 2 Port 1 Port 2
--------------------------------------------------------
1 DOWN DOWN None None
cisco9300#
Port Config:
interface GigabitEthernet1/0/4
switchport trunk native vlan 3002
switchport mode trunk
power inline static max 30000
end
--> 802.3bt capable AP is connected to above port
Observations:
1. Port status is seen down and AP is not powered
cisco9300#sh ip int brief gi1/0/4
Interface IP-Address OK? Method Status Protocol
GigabitEthernet1/0/4 unassigned YES unset down down
cisco9300#
Switch Logs seen:
*Jul 6 13:20:00.067: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/4: PD removed
*Jul 6 13:20:09.058: %ILPOWER-5-DETECT: Interface Gi1/0/4: Power Device detected: IEEE PD
*Jul 6 13:20:09.059: %ILPOWER-5-ILPOWER_POWER_DENY: Interface Gi1/0/4: inline power denied. Reason: insufficient power
Switch Logs in debug mode:
*Jul 6 14:02:24.339: ILP:: ilp enabled in hwidb Gi1/0/4
*Jul 6 14:02:24.339: ILP:: ILP CLI 'no shut' handling ( Gi1/0/4 ) Okay
*Jul 6 14:02:24.339: ILP:: Sending poe coredump msg to slot:1
*Jul 6 14:02:24.340: ILP::
Sending E_ILP_GET_DEBUG_CORE_DUMP IPC message from RP to platform
*Jul 6 14:02:24.340: ILP:: ilp hwidb Gi1/0/4 admstate 3
*Jul 6 14:02:24.340: ILP:: ilp hwidb Gi1/0/4 admstate static 3
*Jul 6 14:02:24.341: ILP:: ILP CLI 'no shut' handling ( Gi1/0/4 ) Okay
*Jul 6 14:02:24.342: ILP:: ilp enabled in hwidb Gi1/0/4
*Jul 6 14:02:24.343: ILP:: Gi1/0/4: State=NGWC_ILP_SHUT_OFF_S-0, Event=NGWC_ILP_CLI_START_DETECT_EV-17
*Jul 6 14:02:24.343: ILP:: START_DETECT_EV, shutoff_state Gi1/0/4
*Jul 6 14:02:24.343: ILP:: Sending poe detect msg to slot:1 port:4
*Jul 6 14:02:24.344: ILP::
Sending E_ILP_START_IEEE IPC message from RP to platform
*Jul 6 14:02:24.345: ILP:: Rx Response ILP msg: response_code 27, sw_num 1
*Jul 6 14:02:24.345: ILP:: ILP msg: received E_ILP_GET_DEBUG_CORE_DUMP
*Jul 6 14:02:24.345: ILP:: Inline power process coredump for switch 1
*Jul 6 14:02:24.352: ILP:: ilpsm posting link down event Gi1/0/4
*Jul 6 14:02:24.356: ILP:: ilpsm posting link down event Gi1/0/4
*Jul 6 14:02:24.363: ILP:: ilpsm posting link down event Gi1/0/4
*Jul 6 14:02:26.338: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/4, changed state to down
*Jul 6 14:02:28.363: ILP:: Gi1/0/4: State=NGWC_ILP_DETECTING_S-2, Event=NGWC_ILP_WAIT_LINK_DOWN_TIMER_EV-42
*Jul 6 14:02:28.363: ILP:: Sending poe detect msg to slot:1 port:4
*Jul 6 14:02:28.363: ILP::
Sending E_ILP_START_IEEE IPC message from RP to platform
*Jul 6 14:02:28.363: ILP:: timer event, Null swidb .
*Jul 6 14:02:28.484: ILP::
Sending E_ILP_SET_ICUTOFF IPC message from RP to platform
*Jul 6 14:02:28.484: ILP:: Sending icutoff current msg to slot:1 port:21
*Jul 6 14:02:28.484: ILP::
Sending E_ILP_SET_ICUTOFF IPC message from RP to platform
Note: AP is powered (via BT power) successfully when power limit is removed on switch port
