cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
805
Views
0
Helpful
2
Replies

CML2.2.2 CSR1000V Subinterface Issue?

gmcdwllntwrk
Level 1
Level 1

In CML2.2.2, I have one csr1000v interface connected to one iosvl2 interface.

On the router side, I've configured subinterfaces, and on the switch side, I've configured a trunk interface plus corresponding SVIs.  No ping.  My question:  Is there a known issue with subinterfaces on the csr1000v? 

TIA.

2 Accepted Solutions

Accepted Solutions

Harold Ritter
Level 12
Level 12

Hi @gmcdwllntwrk ,

 

This is due to the way the CSR1000v handles subinterfaces.

 

Please refer to the following post for more information on how to solve the issue.

 

https://community.cisco.com/t5/ipv6/ipv6-address-on-subinterfaces/td-p/4504574

 

Regards,

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

View solution in original post

gmcdwllntwrk
Level 1
Level 1

Thanks So Much Harold,

Trying to get that port-channel working, I was questioning my insanity for a while there.

I wanted to model a connection to a trunk interface on the far side, so I did it like this, and it works.

Note: It may be a bit unusual to have a routing native vlan on the switch, but To everything, There is a season, and for every config, there is a reason...

 

RTR1 (CSR1000V)SW (IOSvL2)
! In lieu of a port-channel i/f! On this side a trunk w/ native VL 10
  
bridge-domain 10 vlan 10
bridge-domain 11 vlan 11
bridge-domain 12 vlan 12
  
interface GigabitEthernet1interface GigabitEthernet0/0
 no shut switchport trunk allowed vlan 10-12
 service instance 10 ethernet switchport trunk encapsulation dot1q
  encapsulation untagged switchport trunk native vlan 10
  bridge-domain 10 switchport mode trunk
 ! negotiation auto
 service instance 11 ethernet no shut
  encapsulation dot1q 11!
  bridge-domain 11interface Vlan10
 ! ip address 10.10.10.2 255.255.255.0
 service instance 12 ethernet no shut
  encapsulation dot1q 12!
  bridge-domain 12interface Vlan11
 ! ip address 11.11.11.2 255.255.255.0
! no shut
interface BDI10!
 ip address 10.10.10.1 255.255.255.0interface Vlan12
 no shut ip address 12.12.12.2 255.255.255.0
! no shut
interface BDI11!
 ip address 11.11.11.1 255.255.255.0 
 encapsulation dot1Q 11 
 no shut 
! 
interface BDI12 
 ip address 12.12.12.1 255.255.255.0 
 encapsulation dot1Q 12 
 no shut 
! 

View solution in original post

2 Replies 2

Harold Ritter
Level 12
Level 12

Hi @gmcdwllntwrk ,

 

This is due to the way the CSR1000v handles subinterfaces.

 

Please refer to the following post for more information on how to solve the issue.

 

https://community.cisco.com/t5/ipv6/ipv6-address-on-subinterfaces/td-p/4504574

 

Regards,

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

gmcdwllntwrk
Level 1
Level 1

Thanks So Much Harold,

Trying to get that port-channel working, I was questioning my insanity for a while there.

I wanted to model a connection to a trunk interface on the far side, so I did it like this, and it works.

Note: It may be a bit unusual to have a routing native vlan on the switch, but To everything, There is a season, and for every config, there is a reason...

 

RTR1 (CSR1000V)SW (IOSvL2)
! In lieu of a port-channel i/f! On this side a trunk w/ native VL 10
  
bridge-domain 10 vlan 10
bridge-domain 11 vlan 11
bridge-domain 12 vlan 12
  
interface GigabitEthernet1interface GigabitEthernet0/0
 no shut switchport trunk allowed vlan 10-12
 service instance 10 ethernet switchport trunk encapsulation dot1q
  encapsulation untagged switchport trunk native vlan 10
  bridge-domain 10 switchport mode trunk
 ! negotiation auto
 service instance 11 ethernet no shut
  encapsulation dot1q 11!
  bridge-domain 11interface Vlan10
 ! ip address 10.10.10.2 255.255.255.0
 service instance 12 ethernet no shut
  encapsulation dot1q 12!
  bridge-domain 12interface Vlan11
 ! ip address 11.11.11.2 255.255.255.0
! no shut
interface BDI10!
 ip address 10.10.10.1 255.255.255.0interface Vlan12
 no shut ip address 12.12.12.2 255.255.255.0
! no shut
interface BDI11!
 ip address 11.11.11.1 255.255.255.0 
 encapsulation dot1Q 11 
 no shut 
! 
interface BDI12 
 ip address 12.12.12.1 255.255.255.0 
 encapsulation dot1Q 12 
 no shut 
!