el 02-21-2014 05:36 PM
Buenas tardes, una consulta, tengo un equipo Nexus 5548UP con un modulo N55-M4Q, el cual voy a conectar a un C6509-E, a travez de un enlace de 40G como trunk.
El modulo N55-M4Q, trae 4 puertos c/u es 4 x 10G, sabe alguien de como realizar la configuracion en conjunto a 40G ya que en los manuales no especifica el mode de configuracion en este tipo de Nexus 5548UP, cada interface de las cuatro se tendra que configurar por separado o configurando la primer interface de las 4 las demas lo tomaran automatico?, pero al final es solo un puerto fisico de 40G.
Este es el link del manual al que me refiero:
Anexo configuracion y status:
NEXUS-5548UP# sh int status | be conn
Eth2/1/1 -- sfpAbsent 1 full 10G --
Eth2/1/2 -- sfpAbsent 1 full 10G --
Eth2/1/3 -- sfpAbsent 1 full 10G --
Eth2/1/4 -- sfpAbsent 1 full 10G --
Eth2/2/1 -- connected 1 full 10G QSFP-40G-LR
Eth2/2/2 -- connected 1 full 10G QSFP-40G-LR
Eth2/2/3 -- connected 1 full 10G QSFP-40G-LR
Eth2/2/4 -- connected 1 full 10G QSFP-40G-LR
Eth2/3/1 -- sfpAbsent 1 full 10G --
Eth2/3/2 -- sfpAbsent 1 full 10G --
Eth2/3/3 -- sfpAbsent 1 full 10G --
Eth2/3/4 -- sfpAbsent 1 full 10G --
Eth2/4/1 -- sfpAbsent 1 full 10G --
Eth2/4/2 -- sfpAbsent 1 full 10G --
Eth2/4/3 -- sfpAbsent 1 full 10G --
Eth2/4/4 -- sfpAbsent 1 full 10G --
mgmt0 -- notconnec routed auto auto --
Lo1 -- connected routed auto auto --
NEXUS-5548UP#
NEXUS-5548UP# sh run | section Ethernet2
interface Ethernet2/1/1
interface Ethernet2/1/2
interface Ethernet2/1/3
interface Ethernet2/1/4
interface Ethernet2/2/1
interface Ethernet2/2/2
interface Ethernet2/2/3
interface Ethernet2/2/4
interface Ethernet2/3/1
interface Ethernet2/3/2
interface Ethernet2/3/3
interface Ethernet2/3/4
interface Ethernet2/4/1
interface Ethernet2/4/2
interface Ethernet2/4/3
interface Ethernet2/4/4
NEXUS-5548UP#
Saludos.
el 02-25-2014 10:51 AM
Como bien mencionaste cada puerto son 4X10G por lo que tenes que configurar cada sub-puerto por separado, por ejemplo
Eth2/2/1 -- connected 1 full 10G QSFP-40G-LR
Eth2/2/2 -- connected 1 full 10G QSFP-40G-LR
Eth2/2/3 -- connected 1 full 10G QSFP-40G-LR
Eth2/2/4 -- connected 1 full 10G QSFP-40G-LR
Esas son las interfaces que tenes conectadas, por lo que tenes que configurar cada uno por separado
i.e
interface Eth2/2/1
swithcport mode trunk
switchport trunk allowed vlan x-y
el 02-27-2014 06:09 PM
Gracias Yamil por tu respuesta.
Entonces funcionaria como un tipo Etherchannel donde tienen que estar configurados las 4 interfaces con los mismos atributos para no causar un mistmatch.
el 03-11-2014 12:33 PM
Correcto
Descubra y salve sus notas favoritas. Vuelva a encontrar las respuestas de los expertos, guías paso a paso, temas recientes y mucho más.
¿Es nuevo por aquí? Empiece con estos tips. Cómo usar la comunidad Guía para nuevos miembros
Navegue y encuentre contenido personalizado de la comunidad