02-10-2014 04:53 AM
Hi
usually in in Smpt routes i define one Receiving Domain and one Destination Hosts.
I need that the same e-mail is send to multiple destination host.
----> IP1
Mail -----> IROMPORT (receving Domain) --|
---> IP2
How i can do this task ?
Regards
Solved! Go to Solution.
02-10-2014 06:57 AM
This was covered earlier in forums --- I do believe you are trying to accomplish split delivery...
You would be better suited to try a message filter similar to the following --->
duplicate_copy:
if (true)
{
bcc ("$EnvelopeRecipients", "$Subject", "$EnvelopeFrom", "reroute.mail.route");
}
the "reroute.mail.route" is an smtp route that points to the duplicate receiving server. So you could use this to copy all incoming mail from one ESA to another for lab testing purposes if you defined the second ESA as reroute.mail.route.
Hope this helps!
-Robert
(*If you have received the answer to your original question, and found this helpful/correct - please mark the question as answered, and be sure to leave a rating to reflect!)
02-10-2014 08:02 AM
You can use IP, if DNS is not resolvable.
I tested w/ IP just now - and delivery succeeded.
Preferable with SMTP routes, the destination should be:
Enter the destination host for this domain. You may use additional notation to configure these settings:
May take some testing/editing from your side in-order to assure the final/secondary destination acceptance as you intend...
02-10-2014 05:18 AM
Fabio,
Please refer to:
How to specify multiple hosts in the alt-mailhost() action
Knowledge Base Answer ID: 844
http://tools.cisco.com/squish/CF906
You can achieve what you are looking for using the function alt-mailhost().
Also, please consider reading the section: Alter Delivery Host Action
In the "Cisco IronPort AsyncOS 7.6 for Email Advanced Configuration Guide", Chapter 6 Using Message Filters to Enforce Email Policies.
I hope this helps.
-Valter
02-10-2014 06:32 AM
Hi Valther
thanks for your answer.
i read the Manual and the KBA 844.
But on kba is writen :
The hosts will be used in a round robin fashion to deliver messages to this domain.
The filter action and smtproute entry will alternate between the hosts 192.168.2.1 and 192.168.2.2.
Filter action:
alt-mailhost('althost.example.com'); The hosts will be used in a round robin fashion to deliver messages to this domain.
The filter action and smtproute entry will alternate between the hosts 192.168.2.1 and 192.168.2.2.
Filter action:
alt-mailhost('althost.example.com');
This mean that i've to write a filter like alt-mailhost('192.168.2.1,192.168.2.2); ?
I don't need round robin deliver.
I need that the same e-mail is send to both mail server.
Regards
02-10-2014 06:57 AM
This was covered earlier in forums --- I do believe you are trying to accomplish split delivery...
You would be better suited to try a message filter similar to the following --->
duplicate_copy:
if (true)
{
bcc ("$EnvelopeRecipients", "$Subject", "$EnvelopeFrom", "reroute.mail.route");
}
the "reroute.mail.route" is an smtp route that points to the duplicate receiving server. So you could use this to copy all incoming mail from one ESA to another for lab testing purposes if you defined the second ESA as reroute.mail.route.
Hope this helps!
-Robert
(*If you have received the answer to your original question, and found this helpful/correct - please mark the question as answered, and be sure to leave a rating to reflect!)
02-10-2014 07:10 AM
Hi Robert
this is what exacly i need.
Only one question :
in your exaple :
did "reroute.mail.route" need to have a DNS entry ?
Regards
02-10-2014 08:02 AM
You can use IP, if DNS is not resolvable.
I tested w/ IP just now - and delivery succeeded.
Preferable with SMTP routes, the destination should be:
Enter the destination host for this domain. You may use additional notation to configure these settings:
May take some testing/editing from your side in-order to assure the final/secondary destination acceptance as you intend...
02-11-2014 06:09 AM
Hi Robert
thanks for your your answer.
You solved my issue.
Regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide