09-09-2011 07:09 AM - edited 03-10-2019 06:23 PM
Hello,
When I try to add CAS to CAM a cannot choose a OOB Virtual Gateway or OOB Real-IP Gateway, because these operation modes are absent in Type list.
What can be reason it?
09-09-2011 07:56 AM
Anton,
What version of NAC are you running?
Robert
09-09-2011 08:17 AM
Anton,
Another question i have for you is what licenses are you running on the CAM?
Robert
09-09-2011 08:41 AM
Hello Robert,
version 4.8.2
It depends on the license?and where can I find the license it?
Thanks for you time!
09-09-2011 09:03 AM
Anton,
Could you send me a screen shot of the licenses you have loaded on the CAM?
You can post it here or send to my email: rroulhac@cisco.com.
Thanks,
Robert
09-12-2011 06:16 AM
>>>> От: Robert E Roulhac Jr [rroulhac@cisco.com]
>>>> Отправлено: 9 сентября 2011 г. 21:22
>>>> Кому: Каширин Антон
>>>> Тема: Re: NAC Server type
>>>>
>>>> Anton,
>>>>
>>>> I am going to to my best to help you get to the bottom of this. I need for
>>>> you to take a screen shot of the licenses that you have for the CAS in the
>>>> CAM.
>>>>
>>>> There is a license type that we need to see to know if you have the right
>>>> license.
>>>>
>>>> Robert
=============================
>>> Anton,
>>>
>>> Thanks you for the image. What it looks like is that you need to go to the
>>> CAM and add in the licenses for the CAS.
>>>
>>> How to:
>>> 1. click on "Browse".
>>> 2. browse to the lic file for the CAS.
>>> 3. select "Install License"
>>> 4. then go back and attempt to add the CAS into the CAM and see if the
>>> missing options appear.
>>>
>>> Let me know if this works for you.
>>>
>>> Grace and Peace,
>>>
>>> Robert
==============================
>>> Robert,
>>> when I try to add a license, the following message:
>>> An error occurred while adding the license file. Licensed MAC Address does
>>> not
>>> match. CCA-OB-SERVER-FO feature failed validation.
>>>
>>> tell me, what should I do?
>>>
>>> Regards,
>>> Anton Kashirin
>>> Microtest Ltd
================================
Kanton,
>>
>> Be sure that you have the correct MAC address of the CAS with the correct
>> license file.
>>
>> Robert
=================================
>> Robert,
>> Yes, I'm sure.
>> the license for CAS is registered MAC E4:1F:13:F1:B0:18. It is MAC address of
>> eht0 primary CAS in HA:
>>
>> [root@msk-ncuks-cas246 ~]# ifconfig
>> eth0 Link encap:Ethernet HWaddr E4:1F:13:F1:B0:18
>> inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.240
>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>> RX packets:20303 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:20043 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:3369375 (3.2 MiB) TX bytes:3429475 (3.2 MiB)
>> Interrupt:169
>>
>> eth1 Link encap:Ethernet HWaddr E4:1F:13:F1:B0:19
>> inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.240
>> UP BROADCAST MULTICAST MTU:1500 Metric:1
>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
>> Interrupt:50
>>
>> fake0 Link encap:Ethernet HWaddr 00:01:02:03:04:05
>> inet addr:x.x.x.x Bcast:255.255.255.255 Mask:0.0.0.0
>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:19521 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:0 (0.0 b) TX bytes:3165277 (3.0 MiB)
>>
>> fake1 Link encap:Ethernet HWaddr 00:01:02:03:04:05
>> inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.240
>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
>>
>> fake2 Link encap:Ethernet HWaddr 00:01:02:03:04:05
>> inet addr:x.x.x.x Bcast:255.255.255.255 Mask:0.0.0.0
>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
>>
>> fake4 Link encap:Ethernet HWaddr 00:01:02:03:04:05
>> inet addr:x.x.x.x Bcast:255.255.255.255 Mask:0.0.0.0
>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
>>
>> lo Link encap:Local Loopback
>> inet addr:x.x.x.x Mask:255.0.0.0
>> UP LOOPBACK RUNNING MTU:16436 Metric:1
>> RX packets:1615 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:1615 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:0
>> RX bytes:160207 (156.4 KiB) TX bytes:160207 (156.4 KiB)
>>
>>
>>
>> Regards,
>> Anton Kashirin
=======================================
> Anton,
>
> It looks like there is a licensing issue that we need to fix first. First
> attempt all combibnations with the license and the MAC addresses that you
> have ofn both of the CASes. IF this doesn't work we will need to be sure
> there are no issues with the licenses that were given to you.
>
> This could be done by reaching out to the licensing team at Cisco.
>
> Send an email explaining the issue in detail to licensing@cisco.com.
>
> Once you get the CAS license successfully loaded into the CAM then you
> should be able to see what options you have based on the license you have
> and the other two options should be available.
>
> If you would like CC me to the email you send the the licensing team.
>
> Grace and Peace,
>
> Robert E Roulhac Jr
=======================================
> Robert,
> Thanks for your help! I found mistake. The license for CAS must register for
> MAC address of primary CAM, but not CAS.
> I issue my problem with licensing@cisco.com.
> Have a nice day!
>
>
> Regards,
> Anton Kashirin
======================================
Anton,
So you have loaded the license and now the options that you were looking for
are available?
Robert
======================================
Robert,
Yes it is. I loaded the license and now options "adding OOB type CAS" is available.
Regards,
Anton Kashirin
Microtest Ltd
======================================
Anton,
Great! Glad i could help!
If there is anything else i can do please let me know.
Robert E Roulhac Jr
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide