01-13-2006 04:47 AM - edited 03-10-2019 02:26 PM
Hi there,
i am trying to get the radius attribute 198 from dial-in router (AS5300, C2610) with ios 12.3.
With "debug radius" the following output apears:
*Mar 1 01:06:02.679: RADIUS: Acct-Session-Id [44] 10 "00000009"
*Mar 1 01:06:02.679: RADIUS: Framed-Protocol [7] 6 PPP
[1]
*Mar 1 01:06:02.679: RADIUS: Framed-IP-Address [8] 6 192.168.1.1
*Mar 1 01:06:02.679: RADIUS: Vendor, Cisco [26] 35
*Mar 1 01:06:02.679: RADIUS: Cisco AVpair [1] 29 "connect-progress=L
AN Ses Up"
*Mar 1 01:06:02.679: RADIUS: Acct-Session-Time [46] 6 23
*Mar 1 01:06:02.683: RADIUS: Acct-Input-Octets [42] 6 1377
*Mar 1 01:06:02.683: RADIUS: Acct-Output-Octets [43] 6 106
*Mar 1 01:06:02.683: RADIUS: Acct-Input-Packets [47] 6 14
*Mar 1 01:06:02.683: RADIUS: Acct-Output-Packets [48] 6 7
*Mar 1 01:06:02.683: RADIUS: Acct-Terminate-Cause[49] 6 user-request
[1]
*Mar 1 01:06:02.683: RADIUS: Vendor, Cisco [26] 39
*Mar 1 01:06:02.683: RADIUS: Cisco AVpair [1] 33 "disc-cause-ext=PPP
Receive Term"
*Mar 1 01:06:02.683: RADIUS: Authentic [45] 6 RADIUS
[1]
*Mar 1 01:06:02.687: RADIUS: User-Name [1] 6 "test"
*Mar 1 01:06:02.687: RADIUS: Acct-Status-Type [40] 6 Stop
[2]
*Mar 1 01:06:02.687: RADIUS: Vendor, Cisco [26] 16
*Mar 1 01:06:02.687: RADIUS: cisco-nas-port [2] 10 "BRI0/0:1"
*Mar 1 01:06:02.687: RADIUS: NAS-Port [5] 6 30001
*Mar 1 01:06:02.687: RADIUS: Vendor, Cisco [26] 26
*Mar 1 01:06:02.687: RADIUS: Cisco AVpair [1] 20 "interface=BRI0/0:1
"
*Mar 1 01:06:02.687: RADIUS: NAS-Port-Type [61] 6 ISDN
[2]
*Mar 1 01:06:02.691: RADIUS: Calling-Station-Id [31] 12 "3334277535"
*Mar 1 01:06:02.691: RADIUS: Called-Station-Id [30] 8 "289981"
*Mar 1 01:06:02.691: RADIUS: Service-Type [6] 6 Framed
[2]
*Mar 1 01:06:02.691: RADIUS: NAS-IP-Address [4] 6 192.168.255.104
*Mar 1 01:06:02.691: RADIUS: Acct-Delay-Time [41] 6 0
Where is the attribute 198?
Thanks,
Oliver
Solved! Go to Solution.
01-16-2006 05:35 AM
Hello Oliver,
according to "Additional Vendor-Proprietary RADIUS Attributes" at
http://www.cisco.com/en/US/products/sw/iosswrel/ps1826/products_feature_guide09186a0080080efc.html
there should be additionally
radius-server host x.x.x.x non-standard
in the config to inform the router, that other attributes will be used as well.
for a commad syntax in IOS 12.0
Hope this helps!
Regards, Martin
01-14-2006 09:49 AM
Hello,
would it be possible to post the relevant part of the config? Which Radius server is involved?
Regards, Martin
01-16-2006 12:37 AM
Hello Martin,
here is the information:
Cisco:
...
aaa new-model
!
!
aaa group server radius hamlet
server x.x.x.x auth-port 1812 acct-port 1813
!
aaa group server radius dialin-user
server x.x.x.x auth-port 1812 acct-port 1813
!
aaa authentication login default group hamlet local
aaa authentication sgbp default local
aaa authentication ppp default group dialin-user
aaa authorization exec default group hamlet
aaa accounting network default start-stop group dialin-user
aaa session-id common
...
radius-server host x.x.x.x auth-port 1812 acct-port 1813 key 7 xxx
A1507
radius-server host x.x.x.x auth-port 1812 acct-port 1813 key 7 xxx
radius-server vsa send accounting
radius-server vsa send authentication
We are using FreeRadius 0.8.1.
Regards,
Oliver
01-16-2006 05:35 AM
Hello Oliver,
according to "Additional Vendor-Proprietary RADIUS Attributes" at
http://www.cisco.com/en/US/products/sw/iosswrel/ps1826/products_feature_guide09186a0080080efc.html
there should be additionally
radius-server host x.x.x.x non-standard
in the config to inform the router, that other attributes will be used as well.
for a commad syntax in IOS 12.0
Hope this helps!
Regards, Martin
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide