cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2736
Views
5
Helpful
5
Replies

TrustSec ACL and VRF design questions

deyster94
Level 5
Level 5

We are working on setting up TrustSec for a retirement community.  They are going to use it to segment their residents internet from the rest of their networks.  What we are trying to find out is the following:

1. What is the size of the ACL's we can use in TrustSec

2. Can we build out the vlan's for TrustSec in a separate VRF.

TIA,

Dan

2 Accepted Solutions

Accepted Solutions

jeaves@cisco.com
Cisco Employee
Cisco Employee

Just going through the community questions and saw this was unanswered.

Sorry for the delay, your retirement community project is probably completed by now but wanted to reply anyway.

The supported size of the  SGACL's is product dependent but is not generally a limiting factor. Remember that SGACL's are a list of L4 ports with no IP information, hence are much smaller than equivalent ACL's.

For example, a 3850 supports 680 L4 SGACE entries, a Cat9300 supports 5000 and so on..

Yes, TrustSec is VRF aware. Dynamic and Static mappings are placed in VRFs and propagation is carried out per VRF.

View solution in original post

Hi,

there would need to be an SXP connection from ISE to each VRF on the switch. All mappings on ISE would then be duplicated to each VRF.

If you would like to have different mappings in each VRF then you can segregate mappings in ISE by using ISE SXP domains. Then, ISE SXP domain1 would have an SXP connection to switch VRF1, ISE SXP domain2 an SXP connection to switch VRF2 etc.

I wrote a guide for an SDA border deployment but the concept is the same, check it out here:

https://community.cisco.com/t5/security-documents/policy-enforcement-within-sda-border/ta-p/3646816

Hope that helps.

 

View solution in original post

5 Replies 5

jeaves@cisco.com
Cisco Employee
Cisco Employee

Just going through the community questions and saw this was unanswered.

Sorry for the delay, your retirement community project is probably completed by now but wanted to reply anyway.

The supported size of the  SGACL's is product dependent but is not generally a limiting factor. Remember that SGACL's are a list of L4 ports with no IP information, hence are much smaller than equivalent ACL's.

For example, a 3850 supports 680 L4 SGACE entries, a Cat9300 supports 5000 and so on..

Yes, TrustSec is VRF aware. Dynamic and Static mappings are placed in VRFs and propagation is carried out per VRF.

Hi,

When you say Trustsec is VRF aware, what mechanisms need to be in place to propagate trustsec tags from ISE to multiple VRFs on a switch? Do I need an SXP definition to ISE to get sgt's from ISE to register outside the default VRF on the switch? Are there any How To's or Cisco Documentation on doing TrustSec with VRF's?

 

Hi,

there would need to be an SXP connection from ISE to each VRF on the switch. All mappings on ISE would then be duplicated to each VRF.

If you would like to have different mappings in each VRF then you can segregate mappings in ISE by using ISE SXP domains. Then, ISE SXP domain1 would have an SXP connection to switch VRF1, ISE SXP domain2 an SXP connection to switch VRF2 etc.

I wrote a guide for an SDA border deployment but the concept is the same, check it out here:

https://community.cisco.com/t5/security-documents/policy-enforcement-within-sda-border/ta-p/3646816

Hope that helps.

 

Hi,

there would need to be an SXP connection from ISE to each VRF on the switch. All mappings on ISE would then be duplicated to each VRF.

If you would like to have different mappings in each VRF then you can segregate mappings in ISE by using ISE SXP domains. Then, ISE SXP domain1 would have an SXP connection to switch VRF1, ISE SXP domain2 an SXP connection to switch VRF2 etc.

I wrote a guide for an SDA border deployment but the concept is the same, check it out here:

https://community.cisco.com/t5/security-documents/policy-enforcement-within-sda-border/ta-p/3646816

Hope that helps.

 

Thanks for the quick reply. This definitely helps.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: