06-26-2013 09:42 AM - edited 03-11-2019 07:03 PM
I cannot reach the internet or connect to anyconnect vpn. Current config:
ASA Version 8.4(5)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.50 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
!
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network NETWORK_OBJ_10.0.0.128_26
subnet 10.0.0.128 255.255.255.192
object network OUTSIDE_INTERFACE
host 166.143.123.223
access-list HTTP extended permit icmp any any echo
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPNPOOL 10.0.0.150-10.0.0.181 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static any any destination static NETWORK_OBJ_10.0.0
.128_26 NETWORK_OBJ_10.0.0.128_26 no-proxy-arp route-lookup
nat (outside,inside) source static any interface destination static NETWORK_OBJ_
10.0.0.128_26 NETWORK_OBJ_10.0.0.128_26
!
object network obj_any
nat (inside,outside) dynamic interface
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcp-client client-id interface inside
dhcpd auto_config outside
!
dhcpd address 10.0.0.150-10.0.0.181 inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
anyconnect image disk0:/anyconnect-win-2.5.3046-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_vpn_users internal
group-policy GroupPolicy_vpn_users attributes
wins-server none
dns-server value 10.0.0.50
vpn-tunnel-protocol ssl-client
default-domain value crxxi.local
webvpn
anyconnect ask enable default webvpn
username cisco password 3USUcOPFUiMCO4Jk encrypted privilege 15
tunnel-group vpn_users type remote-access
tunnel-group vpn_users general-attributes
address-pool VPNPOOL
default-group-policy GroupPolicy_vpn_users
tunnel-group vpn_users webvpn-attributes
group-alias vpn_users enable
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
!
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:79e92977ed9f0b6e5aec915a187cd9cc
: end
Solved! Go to Solution.
06-26-2013 10:02 AM
Hi,
I would do the following changes
I would change the VPN Pool to something else than the network that is actually located on your LAN network.
tunnel-group vpn_users general-attributes
no address-pool VPNPOOL
no ip local pool VPNPOOL 10.0.0.150-10.0.0.181 mask 255.255.255.0
ip local pool VPNPOOL 10.0.10.10-10.0.10.40 mask 255.255.255.0
tunnel-group vpn_users general-attributes
address-pool VPNPOOL
I would also remove the Manual NAT configurations currently and add the following configuration
no nat (inside,outside) source static any any destination static NETWORK_OBJ_10.0.0
.128_26 NETWORK_OBJ_10.0.0.128_26 no-proxy-arp route-lookup
no nat (outside,inside) source static any interface destination static NETWORK_OBJ_
10.0.0.128_26 NETWORK_OBJ_10.0.0.128_26
object network LAN
subnet 10.0.0.0 255.255.255.0
object network VPN
subnet 10.0.10.0 255.255.255.0
nat (inside,outside) source static LAN LAN destination static VPN VPN
I dont see anything else that should be causing problems in the configuration
Hope this helps
Please do remember to mark the reply as the correct answer if it answered your question.
- Jouni
06-26-2013 10:02 AM
Hi,
I would do the following changes
I would change the VPN Pool to something else than the network that is actually located on your LAN network.
tunnel-group vpn_users general-attributes
no address-pool VPNPOOL
no ip local pool VPNPOOL 10.0.0.150-10.0.0.181 mask 255.255.255.0
ip local pool VPNPOOL 10.0.10.10-10.0.10.40 mask 255.255.255.0
tunnel-group vpn_users general-attributes
address-pool VPNPOOL
I would also remove the Manual NAT configurations currently and add the following configuration
no nat (inside,outside) source static any any destination static NETWORK_OBJ_10.0.0
.128_26 NETWORK_OBJ_10.0.0.128_26 no-proxy-arp route-lookup
no nat (outside,inside) source static any interface destination static NETWORK_OBJ_
10.0.0.128_26 NETWORK_OBJ_10.0.0.128_26
object network LAN
subnet 10.0.0.0 255.255.255.0
object network VPN
subnet 10.0.10.0 255.255.255.0
nat (inside,outside) source static LAN LAN destination static VPN VPN
I dont see anything else that should be causing problems in the configuration
Hope this helps
Please do remember to mark the reply as the correct answer if it answered your question.
- Jouni
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide