Hi everyone, I am the new user in cisco asa. I met some problem of the configuration in object network, and I am using the packet tracer to do the simulation. I saw some of the tutorial at online and create a object network, it had a lot of option to choose (e.g. range, subnet,fqdm, etc ) But in my object network, it can only chose few option. It was missing the range. Moreover, when I chose NAT, it was not able to select the source option. Hopefully someone can solve my problem and query. Thank you.
[------------------------------------------------
ciscoasa(config-network-object)#?
description Specify description text
host Enter this keyword to specify a single host object
nat Enable NAT on a singleton object
no Remove an object or description from object
subnet Enter this keyword to specify a subnet
-------------------------------------------------]
[-----------------------------------------------------
ciscoasa(config-network-object)#nat (inside,outside) ?
network-object mode commands/options:
dynamic Specify NAT type as dynamic
static Specify NAT type as static
------------------------------------------------------]
[------------------------------------------------------
Cisco Adaptive Security Appliance Software Version 9.2(3)
Device Manager Version 7.1(1)52
Compiled on Mon 15-Dec-14 04:10 by builders
System image file is "disk0:/asa923-k8.bin"
Config file at boot was "startup-config"
ciscoasa up 21 minutes 56 seconds
Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW016 @ 0xfff00000, 2048KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode : CNLite-MC-SSLm-PLUS-2_05
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.09
Number of accelerators: 1
0: Int: Internal-Data0/0 : address is 0090.210B.7D09, irq 11
1: Ext: Ethernet0/0 : address is 0090.210B.7D01, irq 255
2: Ext: Ethernet0/1 : address is 0090.210B.7D02, irq 255
3: Ext: Ethernet0/2 : address is 0090.210B.7D03, irq 255
4: Ext: Ethernet0/3 : address is 0090.210B.7D04, irq 255
5: Ext: Ethernet0/4 : address is 0090.210B.7D05, irq 255
6: Ext: Ethernet0/5 : address is 0090.210B.7D06, irq 255
7: Ext: Ethernet0/6 : address is 0090.210B.7D07, irq 255
8: Ext: Ethernet0/7 : address is 0090.210B.7D08, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8 perpetual
VLANs : 3 DMZ Restricted
Dual ISPs : Disabled perpetual
VLAN Trunk Ports : 0 perpetual
Inside Hosts : 10 perpetual
Failover : Disabled perpetual
Encryption-DES : Enabled perpetual
Encryption-3DES-AES : Enabled perpetual
AnyConnect Premium Peers : 2 perpetual
AnyConnect Essentials : Disabled perpetual
Other VPN Peers : 10 perpetual
Total VPN Peers : 25 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
UC Phone Proxy Sessions : 2 perpetual
Total UC Proxy Sessions : 2 perpetual
Botnet Traffic Filter : Disabled perpetual
Intercompany Media Engine : Disabled perpetual
Cluster : Disabled perpetual
This platform has a Base license.
Serial Number: JMX1536J466
Running Permanent Activation Key: 0xAE057ED9 0x15741D22 0x3C2CDA87 0x910EDED0 0xB7682EC3
Configuration register is 0x1
Configuration has not been modified since last system restart
------------------------------------------------------------------]
