I need to check whether Sourcefire IPS support MQTT or MQTT over SSL TCP protocol in terms of detection of intrusion events, network discovery and etc.
I need to check whether Sourcefire IPS support MQTT or MQTT over SSL TCP protocol in terms of detection of intrusion events, network discovery and etc.
I've searched and searched and have found similar issues, but confusing answers. I have two ASA 5505 appliances running base licenses. I learned this the hard way when I put them into production and discovered random communications issues. This is wh...
We have a VPN setup with EasyVPN with a requirement of secure unit authentication. We are having intermittent issues with it. Sometimes the client ASA will boot up and appears to attempt negotiate the VPN connection. Other times, it comes up fine...
I am running version asa922.8-k8.I have tried via CLI to setup my rules and my access rules are not showing up in ASDM. Here are the rules that I had entered;firewall>enablefirewall#configure terminalfirewall(config)#object network xboxfirewall(confi...
Hi,We use a Cisco ASA. We use an external proxy server from Messagelabs (Symantec). Our clients are configured to use this proxy server. Since a few weeks we are having problems downloading large files. When we talked to Messagelabs about this the co...
Hi,I am tasked with configuring ASA 5515 firewall for 2 factor authentication; first with Smart Card, and then with Application login. so far i have found only 1 document on Cisco site that is similar to what i am trying to achieve.any other help or ...
DearI have a requirement to integrate the Cisco VPN (Cisco VPN Client for Remote Access IPSec VPNs etc.) with OTP system (One Time Password). Anyone have any idea how to achieve this.
hi all,i'm trying to add one of our 5525-X into our solarwinds orion. just wanted to know if temperature OID is supported?i tried to list "resources" for the ASA but it's only giving me CPU, memory, interfaces, etc. but there's no option to monitor i...
Hi Everyone, I configured port porwarding for our internal server as we have 1 public IP only.It is working fine.Need to confirm if we access the server from outside world then first thing that will happen isNAT and then it will look for ACL on outs...
I have never messed with either a ASA5505 or any of the PIX line firewalls. I am now being tasked to configure one from the settings that I was given in a text file that was taken from the PIX. I can't seem to get the PIXtoASA tool since it is some...
if there is a signature's ip range not covered new victims' ip addresses in ISP,is it a good practice to set source and destination ip with any ip ?will it slow down the performance?
Hi Everyone, I have only single Public IP on ASA outside interface.Server is connected to inside network of ASA.I want server should be reachable from internet on port 443.I try the static nat config on ASAnat (inside,outside) ?configure mode command...
Hey, I have an ASA 5525, I have to asa image files loaded in flashwhen I do a 'sho run' I do not seeboot system disk0:/asa825-k8.binbut I know it's using this image because when I do 'sho bootvar' I seeBOOT variable = disk0:/asa825-k8.bin When I att...
Hi all I have a Cisco Pix 515e with 256mb, my license that says vpn-peer unlimited, but I would like to know exactly how many vpn with the amount of memory I have I can connect to my device. Thanks.
Dear all,UN-NAT for those type of rules stopped after upgrading from 8.4(4)1 to 8.4(7)23:nat (inside,dmz) source static obj-192.168.50.182 obj-1.1.1.1 packet-tracer 8.4(4)1:Phase: 1Type: ACCESS-LISTSubtype: Result: ALLOWConfig:Implicit RuleAdditional...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-14-2024 01:25 PM | ||
08-14-2024 08:06 AM | ||
08-08-2024 06:44 PM | ||
08-08-2024 06:24 AM | ||
08-06-2024 09:01 AM |
User | Count |
---|---|
9 | |
8 | |
7 | |
4 | |
4 |