Hi,I've written a nice simple QoS setup for VPN clients on an ASA5510 and it works perfectly for IPSEC clients.class-map vpn-qos match flow ip destination-address match tunnel-group vpn-grouppolicy-map vpn-policy class vpn-qos priorityservice-pol...
Cisco PIX Security Appliance Software Version 8.0(2)Device Manager Version 6.1(5)51 Cisco PIX Security Appliance Software Version 8.0(2)Device Manager Version 6.1(5)51Running VPN on this device with an internal DHCP Pooltunnel-grou...
Setup new Cisco 861 and working well for a new BTNet line for the customer. Changed the firewall using CCP from Zone to Classic Firewall. Worked great all day and configured what I needed to do. Now, with CCP (version 2.6) have the following message:...
G'day All, I am have just completed my first ASA install using 8.4 software, I was ok with 8.2 and prior for NAT, but I am running into an issue with the 8.4 setup. I have a 5585 that is running multiple contexts, one of the contexts connects to a ci...
HI,I was polling my ASA on OP manager which was reside on INSIDE zone now we move OP manager on DMZ. Now ASA not showing ACTIVE CONNECTION and CPU Usage in OP manager.below are snmp configuration.snmp-server host DMZ A.B.C.D community cisco version 2...
I need some help getting my Exchange Server to be able to send out emails. Can someone review my Pix config and verify that the setting are correct so I can elminate the Pix from the problem?User Access VerificationPassword:Type help or '?' for a li...
Hi, I know this topic was already discussed before, and I already tried their solution but nothing happened. Bear with me if I'll post this again.Our company’s Cisco ASA 5520 CPU usage drastically increased up to 93% after installing the antivirus o...
Hi,How can I select specifc traffic for QoS when a VPN client connects?I have:class-map vpn-qos match flow ip destination-address match tunnel-group vpn-groupTo prioritise all traffic for a VPN group, but what of I want to only prioritise their HTTP ...
Hi all,Need to know that how can i check that ASA is passing traffic?Also what command we can use to make sure VPN is working fine.Need to know some troubleshooting commandsThanksMAhesh
Hello all,This may be a fairly simple question to answer, but I did some searching and couldn't find a good answer. By default ASA's will allow traffic from a high security interface to a lower secuirt interface. Such as the inside(100) to outside(0)...
Hi there,Sorry for "spamming" this forum but we're new to the ASA and really want to get the most out of it.We're running three networks (inside, outside and dmz). Inside is 10.0.1.0/24, dmz is 10.0.2.0/24, outside is a static ip allocated by our ISP...
I see following message very frequent on ASA ASDM Syslog messages window; what could be possible reason of these messages and what is the remedy to it.[ Scanning] drop rate-1 exceeded. Current burst rate is 42 per second, max configured rate is 10; C...
I'm having some issues trying to get the Site 3: VPN Client to be able to ping to the Site 2: Server. I have Just built the tunnel from Site1 to Site 2 and now have traffic flowing great from Site 1 to Site 2. Site 3 clients can get to Site 1 clien...
Hi there,We recently purchases the Cisco ASA 5505 to get familiar with it, possibly buying more appliances for our branch offices. However, since the appliance is installed, our SIP telephones no longer register with our SIP service provider.The SIP ...
We've read everything about inspecting SIP packets and allowing them to pass through on port 5060, the default SIP port. However, our setup requires the ASA 5505 to allow SIP on ports 5060, 5160 and 5260.Is this possible with the ASA 5505?If it's not...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
