About Tang-Suan Tan

Tang-Suan Tan · 10-28-2020

Hi all, I tried to find the way to shut down the Appliance by GUI or CLI but cannot got it in FMC 750. Attached some possible ways for your reference but they do not have shut down appliance option. In Greenshot 20201029091449.jpg, it shows only mana...

Tang-Suan Tan · 08-11-2020

Hi all, I have problem on the logging type in Firepower management centre. It has: ALERT, CRIT, DEBUG, EMERG, ERR, INFO, NOTICE and WARNING. The defualt is ALERT. What is the selection include all? Is it INFO include ALERT and all information? thanks...

Tang-Suan Tan · 08-10-2020

Hi all, I have set the Action Alert and Access Control Policy on the IPS Firepower Managment Centre for two IPS Censors.The Syslog for the Action Alert also has been set and they are route between the IPS FMC and Censors. May I have the helps below i...

Tang-Suan Tan · 07-29-2020

Hi all, I issued the Failover Active on Standby ASA and No Failover Active on Active ASA but both ASA all cannot change the state. At the time after issuing this command, the SSH session on the ASA also drop and has to restart session again. The two ...

Tang-Suan Tan · 07-24-2020

Hi all, I want to test my IPS Appliance Firepower 7120 whether can raech to my Syslog server in different subnet by using Ping. So, I ssh into the Appliance but I cannot find a way to exceute the Ping command. Below is the information on the Applianc...

Tang-Suan Tan · 10-29-2020

Hi Marvin, I cannot access the CLI and GUI on this Appliance because of username and password.I don't think I can use CIMC.The worse case is can I press the Power button on this appliance to shutdown?Something like press and hold until it is power do...

Tang-Suan Tan · 10-29-2020

Hi Marvin, I tried the cli but cannot access by my username and password.So, for Cisco Integrated Management Controller, is it have to install on the windows server so that then can use it?Where can I find the software to install? I am in the midst o...

Tang-Suan Tan · 08-14-2020

Hi Marvin, I found out that the Syslog.info does not come with Intrusion Event as picture attached. That is the problem that the Syslog does not come with the Message. This Message is the Intrusion Signature information on the Intrusion event. May I ...

Tang-Suan Tan · 08-12-2020

Hi Marvin, Thanks to your reply. My client shows the below one of example IPS Syslog which contains of Message (IPS signature information) and said why our one does not have that Message information. Below is his example: For example:-Intrusion Event...

Tang-Suan Tan · 08-12-2020

Hi Marvin, Now I have new problem feedback from client.The problem is after I set to Info and also from Syslog output, I can have the output as below: 8/12/2020 11:34Syslog.Info172.23.10.312020-08-12T03:34:29Z n206pdmzip1 IGMSSyslog1 %NGIPS-6-430003:...

Member Since	‎09-13-2010 08:45 PM
Date Last Visited	‎10-30-2020 12:04 AM
Posts	206
Total Helpful Votes Received	9

User Statistics

User Activity

How to shut down IPS Appliance (Censors) by Firepower Management Centre 750 GUI or CLI

Firepower Management Centre 750 Logging Type

Firepower Management Centre 750 Not Generate Log after Syslog and Access Policy has been set

Cisco ASA 5585X Failover No Working

Execute Ping Command in Cisco FirePOWER 7120 v6.4.0.9 (build 62)

Re: How to shut down IPS Appliance (Censors) by Firepower Management Centre 750 GUI or CLI

Re: How to shut down IPS Appliance (Censors) by Firepower Management Centre 750 GUI or CLI

Re: Firepower Management Centre 750 Logging Type

Re: Firepower Management Centre 750 Logging Type

Re: Firepower Management Centre 750 Logging Type