firepower unable to add on firesight
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-05-2016 11:05 PM - edited 02-21-2020 05:40 AM
hi,
i have a ASA-5512x with firepower and firesight. but unable to add firepower on firesight. can ssh firepower from firesight.
any advice.
regards
Aazmi
- Labels:
-
Other Network Security Topics
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-06-2016 02:09 AM
Probably you did something wrong ...
What did you exactly do (both on FP and on FS) and what are the error messages?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-06-2016 04:33 AM
i got the below message ;
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-06-2016 04:38 AM
I have firesight ;
Software Version | 5.4.0 (build 763) |
---|---|
OS | Sourcefire Linux OS 5.4.0 (build126) |
and firepower
Sourcefire Linux OS v5.4.0 (build 127)
Sourcefire ASA5512 v5.4.0 (build 764)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-06-2016 04:44 AM
I would first update FireSight to the newest 5.4.x pactchlevel.
Is the output of "show managers" on FP matching your setup?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-06-2016 04:47 AM
on firepower
show managers
Host : 10.203.5.122
Registration Key : cisco
Registration : pending
RPC Status :
on firesight
same on firesight
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-07-2016 05:22 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-07-2016 05:49 AM
How long did you wait? And how did it fail exactly?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-07-2016 06:01 AM
it took around 9 to 12 min to reach 19%, retry few time and then got the message of failed.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-16-2016 07:45 AM
Hi
I have the same problem when I try to add ASA5506 Firepower to FSM Virtual Appliance on version 6.0.0 (build 1005)
I tried with the version FSM 5.4.0 when I try to patch any version 5.4.1 or 5.4.1.3 it's fails in 7%
Any idea to resolve this problem? I reimage twice my ASA but no way
Thanks
regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-02-2017 07:04 AM
Hi,
Did anyone find a solution, I'm experiencing the same issue while adding the firepower module to Firesight.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-02-2017 07:54 AM
Please tell us the details of your issue or start a new discussion.
There are several different issues mentioned in this thread already.
