Just installed ISE 2.3. added the WLC and attached some Iphone to the WLC. when I go into ISE admin > Context Visibility > Endpoints. The IPhones are showing as Unknown. I tried multiple iphones and all of them say unknown. Is there something I need ...
Forum Posts
Dear Experts,My VPN encryption domain as follows,access-list VPN-ACL extended permit ip host 172.16.99.218 host 192.168.10.22access-list VPN-ACL extended permit ip host 172.16.99.218 host 192.168.10.23My original source IP is 172.16.100.33 which need...
Hello, I am attaching a design for connecting campus layer catalyst Catalyst switches to Data Center N9k switches via a pair of FTD 4100 appliances in (Transparent mode) Active / Standby.The top catalyst L3 switches connect to FTD by regular spanning...
Hi guys, Firstly, please shoot me down if I'm being a moron. Secondly, it's my first time posting, so please point me in the right direction if I'm asking this in the wrong place! I've seen this asked before, however, I can't seem to find a post ...
Hello Guys How can i delete the .PAC file i just imported to cisco asa using cts import-pac command i need to generate new one from cisco ISE Thanks
Hi, I have a problem in connecting working ASA to the primary cluster member. when we connect the standby ASA with primary ASA then it gets rebooted every minute but working fine in standalone mode. Kindly help with the possible resolutions Thank...
hi,we have recently moved to our newly configured ASA5520 from PIX, everything is correct and working fine, except that randomly ASA reboots itself without any message in the syslog. i can't seems to trace anything that what's causing it to happen..A...
Hey I have a large network with a ASA5555-X in middle and about 30-40 ASA's in branch offices. Maintaing ACL lists on the branch office firewalls are a lot of work. Is it possible in any way to IPsec the wanted subnets and use the the main ACL list o...
Hello I've been confused regarding the ASA License, and I've couple of question and I need some to help me with it 1- I've ASA 5516X with FirePOWER Services and I purchased the needed licenses and now the licenses enrolled successfully. current...
Hi all When a client and server use PFS ciphers as part of the TLS session setup, what consideration(s), if any, should be given to an IPS system such as the FTD deployed in the middle to inspect the traffic? My understanding of this whole topic ...
Resolved! ASA isn't Routing Traffic
I've spun up an ASA in packet-tracer and I've set up some device as shown below: PC A - 192.168.1.2 ASA - 192.168.1.1 / 172.16.1.1 PC B - 172.16.1.2 Both PCs are able to ping the ASA but can't get to each other. I've set an all ICMP ACL so I woul...
We have been experiencing periods where the FMC states that it is experiencing high CPU usage. I ran the "top" command it get the output included in the Snapshot taken. it also states that the time is out of sync but when I look at the config it, it ...
Hi, ASA5505 cannot be accessed by console. When trying to access the ASA, CRT show nothing and just keep stuck status without any refusing error message ( it looks like the ASA can keep stuck forever). Please see picture attached. The console cable i...
I downloaded latest geodb file (Sourcefire_GeoDB_Update-2017-10-10-005.sh) from download section but get an error, see screenshot. The file looks OK. ASA 9.8(2) ASDM 7.8(2) FirePower 6.2.2-81
I'm learning how to configure a Cisco ASA using packet tracer and I have a very simple set of rules I need to add. I have other rules to add, as well, but I would like to use these to ask for help so I can know how to begin. Not allow any incoming co...
| User | Count |
|---|---|
| 10 | |
| 5 | |
| 5 | |
| 2 | |
| 1 |
