01-14-2018 11:24 PM - edited 02-21-2020 07:08 AM
Dear guys.
My diagram network as file attached. How can everyone access my web server from internet?
On Vigor DrayTek 3900, I configured NAT port Redirection port with bellow information
Protocol: TCP/UDP Public Port Start: 80 Private IP: 192.168.46.2 Private Port: 80
After , I configure on PIX firewall, I configured as bellow
PIX Version 8.0(3) ! hostname ASA enable password LfltCGAmy0yLzCiC encrypted names ! interface Ethernet0 nameif OUTSIDE security-level 0 ip address 192.168.46.2 255.255.255.0 ! interface Ethernet1 nameif inside security-level 100 ip address 10.46.32.1 255.255.255.0 ! interface Ethernet2 nameif DMZ security-level 50 ip address 10.46.31.1 255.255.255.0 ! passwd 2KFQnbNIdI.2KYOU encrypted ftp mode passive object-group network inside-subnet network-object 10.46.32.0 255.255.255.0 access-list outside extended permit tcp any host 10.46.31.199 eq www pager lines 24 logging asdm informational mtu inside 1500 mtu OUTSIDE 1500 mtu DMZ 1500 no failover icmp unreachable rate-limit 1 burst-size 1 asdm image flash:/asdm-603.bin no asdm history enable arp timeout 14400 access-group outside in interface OUTSIDE route OUTSIDE 0.0.0.0 0.0.0.0 192.168.46.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart no crypto isakmp nat-traversal telnet timeout 5 ssh timeout 5 console timeout 0 threat-detection basic-threat threat-detection statistics access-list ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp ! service-policy global_policy global prompt hostname context Cryptochecksum:1f891e1c649b4356c69b69ef2d04b61e
From Internet, I try access address 200.200.200.111 on inernet exploer, but it not successfull. Please help me.
01-15-2018 12:57 AM
Should be something like this:
static (inside,outside) tcp 10.46.31.199 80 192.168.46.2 80 netmask 255.255.255.255
access-list outside extended permit tcp any host 192.168.46.2 eq 80
unfortunately I can't test
HTH
Bogdan
01-15-2018 01:22 AM
@Bogdan Nita wrote:
Should be something like this:
static (inside,outside) tcp 10.46.31.199 80 192.168.46.2 80 netmask 255.255.255.255
access-list outside extended permit tcp any host 192.168.46.2 eq 80unfortunately I can't test
HTH
Bogdan
Thanks for your help, but iit's unsuccessful. I think that you write incorrect because my webserver in DMZ.
This is my startup-config when i changed
QTIASA# show running-config : Saved : PIX Version 8.0(3) ! hostname QTIASA enable password LfltCGAmy0yLzCiC encrypted names ! interface Ethernet0 nameif OUTSIDE security-level 0 ip address 192.168.46.2 255.255.255.0 ! interface Ethernet1 nameif inside security-level 100 ip address 10.46.32.1 255.255.255.0 ! interface Ethernet2 nameif DMZ security-level 50 ip address 10.46.31.1 255.255.255.0 ! passwd 2KFQnbNIdI.2KYOU encrypted ftp mode passive object-group network inside-subnet network-object 10.46.32.0 255.255.255.0 access-list outside extended permit tcp any host 192.168.46.2 eq www pager lines 24 logging asdm informational mtu inside 1500 mtu OUTSIDE 1500 mtu DMZ 1500 no failover icmp unreachable rate-limit 1 burst-size 1 asdm image flash:/asdm-603.bin no asdm history enable arp timeout 14400 static (DMZ,OUTSIDE) tcp 10.46.31.199 www 192.168.46.2 www netmask 255.255.255.255 access-group outside in interface OUTSIDE route OUTSIDE 0.0.0.0 0.0.0.0 192.168.46.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart no crypto isakmp nat-traversal telnet timeout 5 ssh timeout 5 console timeout 0 threat-detection basic-threat threat-detection statistics access-list ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp ! service-policy global_policy global prompt hostname context Cryptochecksum:6ac6f814394e8a3467d173456ac23e76 : end
Please help me/
01-15-2018 11:13 PM
Can you run a packet tracer and post the output ?
packet-tracer input outside tcp 8.8.8.8 1025 192.168.46.2 80
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide