12-30-2023 02:01 PM - edited 12-30-2023 02:07 PM
Dear guys,
I configured port security for interface fast0/2 on switch, according to the aging type and time after 1 minute the switchport must error disable the port and drop the traffic,but nothing happens, please help to resolve it.
Best wishes
Sultan
12-30-2023 02:06 PM
Why errdisable
After 1 min and using aging (you need to add static since you use sticky) the port relearn the mac not go to errdisable
MHM
12-30-2023 02:52 PM
Aging time cause i want to give access to a guest via the switch, so i define 1 minute time limit afterr 1 minute the switchport must go error disable.
Aging type is Absolute!
12-30-2023 03:04 PM
Even if it absolute' the aging will make SW remove mac from port and learn new one.
You want after specific time the host disconnect I think you can not do that with port secuirty you need 802.1x for this task
MHM
12-30-2023 03:08 PM
I read from Cisco book there i two aging type : Absolute and inactivity, once one of these configure along with specific time the port must counter to error-disable. regardless of changing mac from that port. !!!
12-30-2023 03:10 PM
Can you share the cisco book name' let me check it
MHM
12-30-2023 03:14 PM
12-30-2023 03:21 PM
31 Days before your CCNA exam Book.
12-30-2023 03:25 PM
Yes friend'
I read the page and as I mention before it talk about remove mac from table and make port learn new mac.
There is no mention about errdisable.
MHM
12-30-2023 03:31 PM
Exactly absolute and inactivity! once the mac is removed from the current secure address still i can communicate with other PC just it removed the mac from the current secured add nothing else. it seems very useless for or i am wrong.
12-30-2023 03:39 PM - edited 12-30-2023 03:40 PM
No it not useless'
You have SW and you config port secuirty' then your host pc is move and you are admin'
Without aging you need to shut/no shut port to make port learn new mac
With aging' after specific time the port clear mac and learn new mac without need from admin to shut/no shut port
MHM
12-31-2023 12:37 PM
Switch#show port-security interface ethernet 0/3
Port Security : Enabled
Port Status : Secure-up
Violation Mode : Shutdown
Aging Time : 1 mins
Aging Type : Absolute
SecureStatic Address Aging : Disabled
Maximum MAC Addresses : 1
Total MAC Addresses : 1
Configured MAC Addresses : 1
Sticky MAC Addresses : 0
Last Source Address:Vlan : 0050.7966.68e7:1
Security Violation Count : 0
Right i manually added mac address to the port and after 1 mins switch must not try to relearn new mac address because its not sticky. I'm confused mate.
12-31-2023 03:25 PM
swtichport port-security aging type absolute <- this for aging dynamic mac
But you config sticky (which is static mac) so you need
swtichport port-security aging static type absolute
MHM
12-31-2023 03:45 PM
By this config i expect the switch after 1 min release the sticky (dynamically learnt mac pc1) and learn the new mac from pc2.
but when i swap ports the interface counts error-disable.
I'm deeply confused with aging time how it works please simply explain and brief the out put to understand it.
12-31-2023 04:04 PM
There are two type of mac in port secuirty
1- dynamic
2- static a- manual add mac to port b- sticky
So sticky is staitc not dynamic' it really dynamic learn mac but it add to port-secuirty as static mac.
Now port secuirty aging you need to specify static to make port secuirty aging static mac entry (via sticky)
***switchport port-security aging {static | time time | type {absolute | inactivity}}
MHM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide