03-14-2018 12:46 AM - edited 02-21-2020 07:30 AM
Hi all,
I am doing the third upgrade to 6.2.2 version (two upgrades were done without errors) and when I run the readiness check my browser crashed. After reopening the browser the process was stuck. I did not check it and I tried to start it again. Now it is running for 24 hours and it is not possible to stop it. Reboot does not have any affect. Can anyone help me?
Thank you for your help ...and I apologize for my English
Jan
version: 6.2.1
Solved! Go to Solution.
03-14-2018 10:47 PM - edited 03-15-2018 03:29 AM
It could be the best answer but I have a direct solutition. It is from TACman session.
Is a bug in ver. 6.2.1 and stucked process can be removed by theese commands:
1. list of process
root@Sourcefire3D-01:~# OmniQuery.pl -db mdb -e "select hex(uuid),status,body from notification where status = 7;"
root@Sourcefire3D-01:~# OmniQuery.pl -db mdb -e "select hex(uuid),status,body from notification where body like '%eadin%';"
You can see something like this:
root@Sourcefire3D-01:~# OmniQuery.pl -db mdb -e "select hex(uuid),status,body from notification where body like '%eadin%';"
+----------------------------------+--------+---------------------------------------------------------------------------------+
| hex(uuid) | status | body |
+----------------------------------+--------+---------------------------------------------------------------------------------+
| 241AEC6E6CE3313081E0218AAF359562 | 6 | {"literal":"<p><strong>Readiness Check For version: 6.2.2-81</strong><br></p>"} |
| 6DC07704A2DD3DC3BCE8FF662C948F54 | 6 | {"literal":"<p><strong>Readiness Check For version: 6.2.2-81</strong><br></p>"} |
+----------------------------------+--------+---------------------------------------------------------------------------------+
2 rows in set
// The hex number of process is used in another command
2. Deleting process
OmniQuery.pl -db mdb -e 'delete from notification where uuid=unhex ("241AEC6E6CE3313081E0218AAF359562");'
3. Refresh the web page
03-14-2018 12:54 AM
I'd go ahead and open a TAC case in this instance.
The TAC engineer can go into the file system of your FMC and manually delete the incomplete job. It's not something you want to do on your own though.
03-14-2018 10:47 PM - edited 03-15-2018 03:29 AM
It could be the best answer but I have a direct solutition. It is from TACman session.
Is a bug in ver. 6.2.1 and stucked process can be removed by theese commands:
1. list of process
root@Sourcefire3D-01:~# OmniQuery.pl -db mdb -e "select hex(uuid),status,body from notification where status = 7;"
root@Sourcefire3D-01:~# OmniQuery.pl -db mdb -e "select hex(uuid),status,body from notification where body like '%eadin%';"
You can see something like this:
root@Sourcefire3D-01:~# OmniQuery.pl -db mdb -e "select hex(uuid),status,body from notification where body like '%eadin%';"
+----------------------------------+--------+---------------------------------------------------------------------------------+
| hex(uuid) | status | body |
+----------------------------------+--------+---------------------------------------------------------------------------------+
| 241AEC6E6CE3313081E0218AAF359562 | 6 | {"literal":"<p><strong>Readiness Check For version: 6.2.2-81</strong><br></p>"} |
| 6DC07704A2DD3DC3BCE8FF662C948F54 | 6 | {"literal":"<p><strong>Readiness Check For version: 6.2.2-81</strong><br></p>"} |
+----------------------------------+--------+---------------------------------------------------------------------------------+
2 rows in set
// The hex number of process is used in another command
2. Deleting process
OmniQuery.pl -db mdb -e 'delete from notification where uuid=unhex ("241AEC6E6CE3313081E0218AAF359562");'
3. Refresh the web page
03-15-2018 03:28 AM
Yes, that what the TAC would do. The procedure may vary across releases and depending on the exact problem so be VERY careful with the syntax.
NOTE: under step 2 I believe the line should begin: OmniQuery (you left out the "O".)
03-15-2018 03:32 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide