
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-14-2016 11:15 PM - edited 03-12-2019 12:29 AM
Well, how do you reset to factory default the FirePOWER module in ASA
Thanks! :D
Solved! Go to Solution.
- Labels:
-
NGFW Firewalls
Accepted Solutions

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-14-2016 11:21 PM
Hi LJ,
The only way to get back to factory default is to Reimage the module.
Regards,
Dinesh Moudgil
P.S. Please rate helpful posts.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-15-2016 12:56 AM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-14-2016 11:21 PM
Hi LJ,
To reload, or to reset and then reload, the module, enter one of the following commands at the ASA CLI. In multiple context mode, perform this procedure in the system execution space.
Hardware module (ASA 5585-X):
Software module (all other models):
Check this link:
http://www.cisco.com/c/en/us/td/docs/security/asa/asa93/configuration/firewall/asa-firewall-cli/modules-sfr.html#pgfId-1486600
Regards,
Aditya
Please rate helpful posts.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-14-2016 11:33 PM
Hi Aditya,
Thank you for the response,
So if i do 'sw-module or hw-module sfr reset' -this will restart to factory default the Module?

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-15-2016 12:56 AM
Hi LJ,
Regards,
Aditya
Please rate helpful posts.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-14-2016 11:21 PM
Hi LJ,
The only way to get back to factory default is to Reimage the module.
Regards,
Dinesh Moudgil
P.S. Please rate helpful posts.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-17-2016 07:49 PM
HI everyone I just tested Aditya's recommendation, but it DOES NOT WORK
a re-flashing/re-imaging is required to clear the FirePOWER module, be informed ^_^
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-27-2022 05:06 AM
how do you RE- FLASH it is that an option ??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-27-2022 05:55 AM
@jespinosa you can just do "sw-module module sfr uninstall".
If you then want to proceed to build it anew, then see this blog post for many more details: https://community.cisco.com/t5/security-blogs/reimage-firepower-module-in-cisco-5500-x-firewall-models/ba-p/3760395
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-12-2022 04:15 AM
Thanks , for all the information, that worked perfectly,
much appreciated !!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-12-2022 12:42 PM
@jespinosa you're welcome. Please mark my reply as helpful in that case.
