sfr module unknown

[i.pustovalov1]

Hello! I have asa 5506x

Cisco Adaptive Security Appliance Software Version 9.5(1)
Device Manager Version 7.6(1)

Compiled on Wed 12-Aug-15 12:18 PDT by builders
System image file is "disk0:/asa951-lfbff-k8.SPA"

Hardware:   ASA5506, 4096 MB RAM, CPU Atom C2000 series 1250 MHz, 1 CPU (4 cores)
Internal ATA Compact Flash, 8192MB
BIOS Flash unknown @ 0x0, 0KB

and

Mod  Card Type                                    Model              Serial No.
---- -------------------------------------------- ------------------ -----------
   1 ASA 5506-X with FirePOWER services, 8GE, AC, ASA5506            JAD192903QX
 sfr Unknown                                      N/A                JAD192903QX

Mod  MAC Address Range                 Hw Version   Fw Version   Sw Version
---- --------------------------------- ------------ ------------ ---------------
   1 5897.bdad.b2b2 to 5897.bdad.b2bb  1.0          1.1.1        9.5(1)
 sfr 5897.bdad.b2b1 to 5897.bdad.b2b1  N/A          N/A

Mod  SSM Application Name           Status           SSM Application Version
---- ------------------------------ ---------------- --------------------------

Mod  Status             Data Plane Status     Compatibility
---- ------------------ --------------------- -------------
   1 Up Sys             Not Applicable
 sfr Recover            Not Applicable

I have same problem https://supportforums.cisco.com/discussion/12630026/asa-5506-sourcefire-module-stuck-recovery

when i try install PKG i have error:

asasfr-boot>system install ?
asasfr-boot>system install
asasfr-boot>system install ftp://10.0.0.205/asasfr-sys-5.4.1-211.pkg
Mod-sfr 388> asasfr login: [  491.560768]  vda: vda1
Mod-sfr 389> [  495.589311] Adding 4194752k swap on /dev/vda1.  Priority:-1 extents:1 across:41
Mod-sfr 390> 94752k
Verifying
111
Upgrade aborted.

what am I doing wrong?

[i.pustovalov1]

Now I'm trying to install asa952-10-lfbff-k8.SPA, asasfr-5500x-Boot-6.0.0-1005.img and asasfr-SYS-6.0.0-1005.pkg

It's okay.


Once installed .pkg module system requested reboot ... ok. After rebooting, I waited 45 minutes, but nothing happened.
If you try to enter a command asa5506x # session sfr console
Opening console session with module sfr.
Connected to module sfr. Escape character sequence is 'CTRL- ^ X'.

asa5506x # sho mod

Mod Card Type Model Serial No.
-------------------------------------------- ---- - ---------------- -----------
   1 ASA 5506-X with FirePOWER services, 8GE, AC, ASA5506 JAD192903QX
 sfr Unknown N / A JAD192903QX

Mod MAC Address Range Hw Version Fw Version Sw Version
---- ------------ --------------------------------- - ----------- ---------------
   1 5897.bdad.b2b2 to 5897.bdad.b2bb 1.0 1.1.1 9.5 (1)
 sfr 5897.bdad.b2b1 to 5897.bdad.b2b1 N / A N / A

Mod SSM Application Name Status SSM Application Version
---- ------------------------------ ---------------- --------------------------

Mod Status Data Plane Status Compatibility
---- ------------------ --------------------- ------- ------
   1 Up Sys Not Applicable
 sfr Recover Not Applicable




and debug says
DP SFR Msg: SFR flow handle was not populated, so not informing SFR about flow cleanup.